Журналы →  Gornyi Zhurnal →  2016 →  №5 →  Назад

PROCESSING AND COMPLEX USAGE OF MINERAL RAW MATERIALS
Название Automated control of hydrocyclone classification
DOI 10.17580/gzh.2016.05.14
Автор Lvov V. V., Aleksandrova T. N.
Информация об авторе

Saint-Petersburg Mining University, Russia:
V. V. Lvov, Associate Professor, Candidate of Engineering Sciences, opilvv@mail.ru
T. N. Aleksandrova, Head of a Chair, Doctor of Engineering Sciences

Реферат

Ore pretreatment improvement remains yet the most important objective in the mining industry. Processes of classifying in hydrocyclones are of no little significance in mineral grinding, especially in the closed circuit grinding. Operation of cyclones often suffers from low efficiency when properties of feed materials change: solids content, slurry viscosity, grain-size composition. This may cause considerable complications to the process, such as different cut point, slope of separation curves characterizing cyclone separation. Stable classifying using hydrocyclones is the important production task. Underflow of a complete cyclone-and-grinder circuit can be discharged using a rope or an open umbrella. Each of these types of discharge has benefits and shortcomings. The optimized separation is achieved at the transition point between the two types of underflow discharge. The stable and optimized separation using cyclones is feasible through the application of the proposed automated control method. The method consists in measuring the slurry flow rate in cyclone overflow and underflow, the slurry viscosity and the width of opening of the underflow umbrella using a contactless sensor. Depending on the measured values, the cross-section of the outflow nozzle is changed using a special device. The stabilization circuit accounts for boundary grain diameter, considering current viscosity of slurry. The application of this automated control method will enable improved performance of hydroclassifying owing to stabilization of cut point of hydrocyclones.
This study has been carried out in the framework of the project part of governmental assignment for research activity (Assignment No. 5.1284.2014/K dated July 11, 2014).

Ключевые слова Hydroclassifying, hydrocyclone, slurry, rheology, viscosity, separation characteristic, cut point, automated control
Библиографический список

1. Andreev E. E., Blatov I. A., Tikhonov O. N. et al. The influence of rheology and size distribution of ground ore upon the flotation of pechenganickel concentrator. Proceedings of International Conference «Rheology in the Mineral Industry». San-Diego, California, USA, 1997.
2. Kawatra S. K., Eisele T. C. Rheological eff ects in grinding circuits. International Journal of Mineral Processing. 1988. Vol. 22. pp. 251–259.
3. Aguilera G., Arismendy J. Rheological characterization of parameters inside a hydrocyclone through variables obtained from CFD simulation. Proceedings of XXVII International Mineral Processing Congress. Santiago, Chile, 2014. Chapter 16. pp. 41–49.
4. Kawatra S. K., Eisele T. C., Zhang D. X., Rusesky M. T. Effects of temperature on hydrocyclone efficiency. International Journal of Mineral Processing. 1988. Vol. 23. pp. 205–211.
5. Kawatra S. K., Eisele T. C., Zhang D. X., Rusesky M. T. Effects of seasonal temperature changes on autogenous milling performance. WE-AIME Meeting. Las Vegas, Nevada, Feb. 27 — March 2, 1989.
6. Dündar H., Kalugin A., Delgaro M., Palomino A., Türkistali A., Aquino B., Lynch A. Screens and cyclones in closed grinding circuits. Proceedings: XXVII International Mineral Processing Congress. Santiago, Chile, 2014. Chapter 16. pp. 65–75.
7. Povarov A. I. Gidrotsiklony na obogatitelnykh fabrikakh (Hydrocyclones at concentration plants). Moscow : Nedra, 1978. 224 p.
8. Aleksandrova T. N., Aleksandrov A. V., Litvinova N. M., Bogomyakov R. V. Вasis and development of gold loss reduction methods in processing gold-bearing clays in the Khabarovsk territory. Journal of Mining Science. 2013. Vol. 49, No. 2. pp. 319–325.
9. Zhu Guofeng, Liow Jong-Leng. Experimental study of particle separation and the fish-hook effect in a mini-hydrocyclone. Chemical Engineering Science. 2014. Vol. 111. pp. 94–105.
10. Minkov L. L., Krokhina A. V., Dik I. G. Raskhodnye kharakteristiki gidrotsiklona so vstroennym inzhektorom (Spend characteristics of hydrocyclone with embed injector). Teplofizika i aeromekhanika = Thermophysics and Aeromechanics. 2011. Vol. 18, No. 3. pp. 413–426.
11. Minkov L. L., Krokhina A. V., Dik I. G. Gidrodinamicheskie mekhanizmy vliyaniya inzhektsii na klassifikatsionnye kharakteristiki gidrotsiklona (Hydrodynamic mechanisms of injection influence on classifi cation cheracteristics of hydrocyclone). Inzhenerno-fizicheskiy zhurnal = Journal of Engineering Physics and Thermophysics. 2011. Vol. 84, No. 4. pp. 747–758.
12. Dik I. G., Krokhina A. V., Minkov L. L. Upravlenie kharakteristikami gidrotsiklona dopolnitelnym inzhektirovaniem vody (Management of hydrocyclone characteristics by extra water injecting). Teoreticheskie osnovy khimicheskoy tekhnologii = Theoretical Foundations of Chemical Engineering. 2012. Vol. 46, No. 3. pp. 342–352.
13. Napier-Munn T. J., Morrell S., Morrison R. D., Kojovic T. Mineral comminution circuits: their operation and optimization. Brisbane, Australia : JKMRC, University of Queensland, 1996. pp. 324–326.
14. Neesse Th., Farghaly M., Hararah M., Proellss G., Rubarth W., Kaniut P. Higher classifi cation efficiency by hydrocyclone control. Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Journal. 2011. Vol. 2, No. 2. pp. 85–91.
15. Plitt L. R., Kawatra S. K. Estimating the cut (d50) size of classifiers without product particle-size measurement. International Journal of Mineral Processing. 1979. Vol. 5. pp. 364–378.
16. Andreev E. E., Lvov V. V., Romashev A. O. Vliyanie reologii pulpy na pokazateli raboty gidrotsiklonov v tsiklakh mokrogo zamknutogo izmelcheniya (Influence of pulp rheology on indicators of hydrocyclones operation in wet closed grinding cycles). Gornyi Zhurnal = Mining Journal. 2011. No. 2. pp. 42–43.
17. Pershina A. V., Romashev A. O. Vliyanie fizicheskikh svoystv zhelezorudnoy pulpy i geometricheskikh parametrov gidrotsiklona na pokazateli raboty operatsii gidrotsiklonirovaniya (Influence of physical properties of iron ore pulp and geometrical parameters of hydrocyclone on hydrocicloning indicators). Gornyy informatsionno-analiticheskiy byulleten = Mining Informational and Analytical Bulletin. 2015. No. 4. Special issue. pp. 3–9.
18. Andreev E. E., Lvov V. V., Fadina A. V., Tikhonov N. O. Sposob avtomaticheskogo upravleniya gidrotsiklonom (Method of automatic control of hydrocyclone). Patent RF, No. 2504439. Applied: July 17, 2016. Published: January 20, 2014. Bulletin No. 2.

Language of full-text русский
Полный текст статьи Получить
Назад