Журналы →  Chernye Metally →  2016 →  №12 →  Назад

Rolling and other metal forming processes
Название Stress-strained state and forming in drawing of hexagonal sections from a round billet
Автор O. S. Zhelezkov, S. A. Malakanov, S. I. Platov
Информация об авторе

Nosov Magnitogorsk State Technical University (Magnitogorsk, Russia):

Zhelezkov O. S., Dr. Eng., Prof., Chair “Engineering Mechanics and Structural Resistance”, e-mail: ferumoff@mail.ru
Malakanov S. A., Cand. Eng., Head of Department, e-mail: samalakanov@mail.ru
Platov S. I., Dr. Eng., Prof., Head of the Chair “Equipment and Technologies of Metal Processing”, e-mail: mitod_@mail.ru

Реферат

The article presents the results of simulation of drawing process for hexagonal sections from round billets through dies of various designs. Drawing in several passes of a round billet through polyhedral monolithic dies with intermediate operations (such as annealing, surface preparation, etc.) is the most common method of manufacturing of hexagon sections. The large number of technological operations is considered as the main deficiency of the applied technology. Simulation of the drawing process for hexagonal shapes from round billets is conducted using the finite element method. The processes of drawing of hexagonal sections through a die with flat faces and a die with ledges in the working area were investigated. The data on the stress-strained state were obtained and the fi elds of distribution of the radial, circular and axial stresses in the billet during drawing were built. It was found that the ledges in the working area of the die favor formation of hexagon edges and provide reducing of deformation heterogeneity. The rational shape and size of the ledges in the working area were determined; they provide regulated technical documentation for shape and sizes of a section, with reducing of deformation degree. Using a die with the ledges in the working area allows to obtain the required hexagonal section through a single pass, whereas in the case of using dies with flat working area, two or three passes with intermediate heat treatment operations are required. Verifi cation of the results of mathematical simulation was carried out by laboratorial testing, using approved testing machine and a full-scale experiment on the chain drawing machine.

The results of the research were used as the basis for development of the new technical solution (RF patent № 78102 «Die for production of polyhedral shaped sections».

Ключевые слова Drawing, metal forming, dies, hexagonal sections, round billets, simulation, fi nite elements method, stress-strained state, working area
Библиографический список

1. Stal kachestvennaya i vysokokachestvennaya: sortovoy i fasonnyy prokat, kalibrovannaya stal. Chast 1 : sbornik (Quality and highquality stel: bar and profile, sized steel. Part 1 : collection). Moscow, 2004. 146 p. (in Russian)
2. Argunov V. N., Ermanok M. Z., Kharitonovich M. V. et al. Kalibrovanie fasonnykh profiley (Calibration of bar profi les). Moscow : Metallurgiya, 1989. 206 p.
3. Vydrin, V. N., Grosman A. B., Pavlov B. C. et al. Proizvodstvo fasonnykh profiley vysokoy tochnosti (Production of high-accuracy shaped sections). Moscow : Metallurgiya, 1977. 184 p.
4. Zykov Yu. S. Teoriya volocheniya sploshnykh profiley (Solid profile drawing theory). Kiev, 1991. 116 p.
5. Bitkov V. V. Tekhnologiya i mashiny dlya proizvodstva provoloki (Technology and machines for wire production). Ekaterinburg : Ural Branch RAS, 2004. pp. 315–321.
6. Wang, Karen L., Vasilis Argyropoulos. Design and analysis of direct cold drawing of section rods through a single die. Journal of Materials Processing Technology. 2005. Vol. 166. pp. 345–358.
7. Gunasekera J. S., Hoshino S. Analysis of extrusion or drawing of polygonal sections through straightly converging dies. Journal of Engineering for Industry. 1982. Vol. 104. pp. 38–45.
8. Turner L. J., Clough R. W., Martin H. C., Topp L. J. Stiffness and deflection analysis of complex structures. Journal of the Aeronautical Sciences. 1956. Vol. 23, No. 9. pp. 805–824.
9. Zienkiewicz O. C. Numerical analysis of forming pronsses swansa. John Wiley and Sons. 1984. pp. 1–44.
10. Kobayashi S., Oh S.-I., Altan T. Metal forming and the finite element method. 1st ed., Vol. 1. (Series Eds.: Crookall, J.R., Shaw, M.C.) Oxford University Press, Oxford, 1989. 377 p.
11. Parshin B. C., Karamyshev A. P., Nekrasov I. I., Pugin A. I., Fedulov A. A. Prakticheskoe rukovodstvo k programmnomu kompleksu DEFORM-3D (Practical guidance to the software complex DEFORM-3D). Ekaterinburg : Ural Federal University, 2010. 266 p.
12. Zhelezkov O. S., Malakanov S. A., Dampilon V. G. Kompyuternoe modelirovanie protsessa kalibrovaniya shestigrannogo prutka iz iskhodnoy zagotovki kruglogo secheniya (Computer-aided simulation of the process of hexagonal bar sizing from initial round billet). Chernye Metally = Ferrous metals. 2011. No. 6. pp. 65–66.
13. Smirnov-Alyaev G. A. Soprotivlenie materialov plasticheskomu deformirovaniyu (Material resistance to plastic deformation). Third edition, revised. Leningrad : Mashinostroenie, 1978. 368 p.
14. O. S. Zhelezkov, V. G. Dampilon, S. A. Malakanov. Voloka dlya izgotovleniya mnogogrannykh fasonnykh profiley (Wires for manufacturing of many-sided shaped sections). Patent RF, No. 78102 IPC7 V 21 S 3/00. 2008124316/22. Applied: 16.06.2008. Published: 20.11.2008. Bulletin No. 32.

Language of full-text русский
Полный текст статьи Получить
Назад