Journals →  Chernye Metally →  2017 →  #12 →  Back

Machine-building Technologies
New developments of Tula State University
ArticleName Technological inheritance of the properties of an initial billet in the accuracy parameters of extended axisymmetric parts
ArticleAuthor A. S. Yamnikov, O. I. Boriskin, O. A. Yamnikova, I. A. Matveev
ArticleAuthorData

Tula State University (Tula, Russia):

Yamnikov A. S., Dr. Eng., Prof., Chair of Machine-building Technology
Boriskin O. I., Dr. Eng., Prof., Head of the Chair of Instrumental and Metrological Systems, Director of Polytechnic Institute
Yamnikova O. A., Dr. Eng., Prof., Chair of Machine-building Technology
Matveev I. A., Engineer, Post-Graduate, Chair of Machine-building Technology, e-mail: ivan_matveev@list.ru

Abstract

Sheet metal is often used in machine-building mass production for fabrication of initial blanks of pipe-like parts with or without a bottom. This sheet metal is a semiproduct for cutting the rounds with subsequent convolution and deep drawing on press equipment. This technology is characterized by high productivity at a low cost due to the high rate of deformation of asheet blank in press equipment and low cost of sheet products. However, these economic advantages of the described technology are accompanied by large values of technological errors, both in stamped blanks and pipe-like parts made of these blanks by treating the base and butt surfaces in metal cutting machines. It was established via the statistical methods that the exit beyond the tolerance field reaches up to 30 % of the total number of parts in the batch. This can be explained byheterogeneity of the material properties of a blank in cross section, because the impact strength value of sheet metal in the longitudinal direction is 2 times greater than that in the transverse direction. Preparation of a workpiece blank for machining via combined technology, including use of hot-rolled thick-walled tube as initialbillet is an alternative to the described technology. It is followed by cutting operations, preliminary machining of the externaland internal cylindrical surfaces, trimming of the ends and, most importantly, rotational extrusion and drawing. Practical effect of this technology is in homogeneity of the material properties of a blank in its cross section, what finalizes in increased accuracy of straightness of the walls and the axis of manufactured billet. Obtained properties are largely copied to the finished product, providing almost twofold reserve of accuracy, what the opens prospects for further improvements of operating efficiency of these products.

keywords Rolled sheet, hot-rolled pipes, citting, pressing, drawing, technological inheritance, blanks, error copying, product accuracy
References

1. Chuprikov A. O., Ivanov V. V., Yamnikov A. S. Provision of accuracy of manufacturing of thread semi-locks on fine-wall welded shells : monograph. Tula : Izdatelstvo TulGU, 2014. 137 p.
2. Yamnikov A. S., Chuprikov A. O, Matveev I. A. Provision of accuracy of manufacturing of fine-wall rotationally symmetric compound bodies : monograph. Tula : Izdatelstvo TulGU, 2017. 208 p.
3. Ilyukhin A. Yu., Ilyukhina O. V. Provision of fl aring of treated cylindric surface over the billet body. Izvestiya TulGU. Tekhnologiya mashinostroeniya. 2004. Iss. 1. pp. 23–29.
4. Mellor P. B., Parmar A. Plasticity Analysis of Sheet Metal Forming. Mechanics of Sheet Metal Forming. Material Behavior and Deformation Analysis. Proceedings of Symposium. Warren, Michigan. New York — London. 1977. pp. 53–74.
5. Wu M. C., Yeh W. C. Some Considerations in the Endochronic Description of Anisotropie Hardening. Acta Mechanica. 1987. 69, No. 1. pp. 59–76.
6. Wu M. C., Hong H. K., Shiao Y. P. Anisotropie plasticity with application to sheet metals. International Journal of Mechanical Sciences. 1999. 41, No. 6. pp. 703–724.
7. Jacov H., Gorries E. Rollentconstruckzion für Fliebdrücken Kreisyzlindyischer Höhlkörper. Fertigungstechnik und Betrieb. 1965. Bd. 15. ss. 279–283.
8. Kugultinov S. Р., Khisamutdinov R. М., Khisarmtdinov М. R. Tool Creation and Operation System Development for Large Engineering Enterprises. World Applied Sciences Journal (WoS). 2014. No. 30(5). pp. 588–591.
9. Tregubov V. I. Rotary drawing with reduction of the wall of cylindrical details made of pipes on specialized equipment : monograph. Tula : Izdatelstvo TulGU, 2002. 148 p.
10. Tregubov V. I., Yakovlev S. S. et al. Innovation Technological Processes of the Rotary Drawing of Geometrically Complex Axial-symmetric Parts. Kuznechno-shtampovochnoe proizvodstvo. Obrabotka materialov davleniem. 2013. No. 11. pp. 9–16.
11. Yakovlev S. S., Tregubov V. I., Pilipenko O. V. et al. Rotary drawing of axisymmetric shells from anisotropic materials with division of deformation zone. Vestnik mashinostroeniya. 2015. No. 1. pp. 73–78.
12. Dalskiy A. M. Technological heredity in assembly plants. Moscow : Mashinostroenie, 1978. 45 p.
13. MI 199-79. Method of definition of the type of mathematical model of error allocation. Moscow : Izdatelstvo standartov, 1981. 16 p.
14. Gromyko G. L. Statistical theory. Moscow : Infra-M, 2001. 160 p.
15. J. H. Pollard. A handbook of numerical and statistical techniques. Translated from English by V. S. Zanadvorov. Ed.: E. M. Chetyrkina. Moscow : Finansy i statistika, 1982. 344 p.
16. Yamnikov A. S., Matveev I. A. Statistical analysis of accuracy mechanical proceedings of extended details from the stamped preparations like steel cases. Izvestiya TulGU, Tekhnicheskie nauki. 2015. Iss. 5, Part 2. pp. 121–126.
17. N. A. Makarovets, V. I. Tregubov, V. A. Korolkov et al. Axially symmetrical vessels producing method. Patent RF, No. 2295416, IPC8 C21D8/10, C21D8/10. Patent owner: State scientific-industrial enterprie “Splav” (RU). Applied: 27.06.2005. Published: 20.03.2007.
18. Tregubov V. I., Larina M. V., Yakovlev S. S. Effect of technological parameters of metal spinning on geometric values of the cylindrical parts quality. Vestnik mashinostroeniya. 2005. No. 3. pp. 68–71.
19. Matveev I. A. The forecasting accuracy of the parameters of complex products in the software environment Statistica. Izvestiya TulGU, Tekhnicheskie nauki. 2017. No. 8, Part 1. pp. 232–238.
20. Matalin A. A. Engineering technique. Tutorial for mechanical engineering universities, the line “Engineering technique, metal cutting machines and instruments”. Publishing House “Lan”, 2008. 512 p.

Language of full-text russian
Full content Buy
Back