Journals →  Tsvetnye Metally →  2019 →  #3 →  Back

ArticleName Production of rivet wire from billets produced from V65 alloy by electromagnetic crystallization
DOI 10.17580/tsm.2019.03.11
ArticleAuthor Timofeev V. N., Usynina G. P., Motkov M. M., Gudkov I. S.
ArticleAuthorData

1Research and Production Centre of Magnetic Hydrodynamics, Krasnoyarsk, Russia ; 2Siberian Federal University, Krasnoyarsk, Russia:

V. N. Timofeev, CEO1, Head of the Electrotechnology Department2

 

Research and Production Centre of Magnetic Hydrodynamics, Krasnoyarsk, Russia:
G. P. Usynina, Chief Materials Specialist
M. M. Motkov, Head of the Continuous Casting and Plastic Deformation Department
I. S. Gudkov, Lead Specialist at the Department of High-Frequency Currents, e-mail: rdohead@mail.ru

Abstract

The sample light-gauge round ingots continuously cast following a newly developed technique are characterized with a clean and disperse structure. This paper describes a rivet wire production technique based on the use of 9 mm V65 aluminium alloy long-length cast billets produced by electromagnetic crystallization (EMC). When the melt is exposed to high-frequency electromagnetic field, the resultant ingots appear free of such structural flaws as slag inclusions, oxide spots or other defects associated with conventional casting. This technique produces a disperse structure with the size of dendritic cells ~3–6 μm, which is typical of granulated aluminium alloys produced at the cooling rates of 103–104 oC/sec. The authors demonstrate the structural effect occurring in the initial ingot following EMC casting. Following a comparison with the conventional technique which produces rivet wire from pressed billets, it was established that the new EMC casting technique helps increase the yield due to the elimination of flaws caused by casting and pressing. It can also reduce the power and labour costs and increase the output due to less annealing operations required during wire drawing. The paper describes various drawing sequences for the EMC billets and how they influence the metal structure. The paper describes the results of a study that looked at the wires produced from homogenized and non-homogenized billets and the effect of the total degree of cold deformation on the grain size and mechanical properties of the wire produced following the new technique. The authors conducted a series of pilot tests and identified the optimum process that would produce aircraft rivets of the desired quality. This research was funded by the Russian Foundation for Basic Research, the Government of Krasnoyarsk Krai, the Krasnoyarsk Regional Science Foundation and the Research and Production Centre of Magnetic Hydrodynamics under the following research project: Understanding the dynamics of the turbulent flow of the melt under electromagnetic crystallization and how the latter changes the structure and properties of continuously cast light-gauge aluminium alloy billets used for the production of thin wire for aerospace application.

keywords Electromagnetic crystallization, high-frequency electromagnetic field, aluminium alloys, granulated alloys, aviation alloys, super fast crystallization, electromagnetic field crystalization, cast and pressed billet, aircraft rivets
References

1. Shilova E. I. The V65 aluminium alloy for rivets. Aluminium and magnesium alloys. Moscow : Oborongiz, 1959. pp. 113–143.
2. Avdulov A. A., Usynina G. P., Sergeev N. V., Gudkov I. S. Distinctive features of the structure and characteristics of long-length light gauge ingots from aluminium alloys, cast into electromagnetic crystallizer. Tsvetnye Metally. 2017. No. 7. pp. 73–77. DOI: 10.17580/tsm.2017.07.12
3. Archakova Z. N. ed al. Structure and properties of semi-finished products from aluminium alloys: Reference book. 2nd revised edition. Moscow : Metallurgiya, 1984. 408 p.
4. Teleshov V. V., Zakharov V. V. et al. The structure and properties of rivet wire from the V65 alloy depending on the alloy’s chemical composition and the production technique employed. Tekhnologiya legkikh splavov. 2008. No. 1. pp. 25–30.
5. Lopatina E. S., Voroshilov D. S., Zaporozhets O. A. Understanding the process parameters in the production of ingots from the 01417 alloy in an electromagnetic crystallizer. Young People and Science: Proceedings of the 6th National Conference among Undergraduates, Postgraduates and Young Researchers. Krasnoyarsk : Sibirskiy federalnyy universitet, 2011. pp. 31–35.
6. Baake E. et al. Magnetohydrodynamic technology in metallurgy. Intensive course. Specialisation IV. Saint Petersburg : LETI, 2013. 250 p.
7. Getselev Z. N. et al. Continuous casting in an electromagnetic crystallizer. Moscow : Metallurgiya, 1983. 152 p.
8. Pervukhin M. V., Khatsayuk M. Yu., Minakov A. V. Numerical modelling of the dynamics of the free surface and crystallization of the melt in an electromagnetic crystallizer. Induktsionnyy nagrev. 2014. No. 1 (27). pp. 37–42.
9. Masahiro Tani, Masafumi Zeze Takehiko Toh, Keiji Tsunenari. Electromagnetic Casting Technique for Slab Casting. Nippon steel technical report. August 2013. No. 104. pp. 56–61.
10. GOST 9012–59. Metals. Method of Brinell hardness measurement (incl. Revisions 1, 2, 3, 4, 5). Introduced: 01.01.1960.
11. GOST 4784–97. Aluminium and wrought aluminium alloys. Grades (incl. Revisions 1, 2, 3, with amendments). Introduced: 01.07.2000.
12. Hai Hao, Xingguo Zhang, Shan Yao. Improvement of Casting Speed and Billet Quality of Direct Chill Cast Aluminum Wrought Alloy with Combination of Slit Mold and Electromagnetic Coil. Materials Transactions. 2007. Vol. 48, No. 8. pp. 2194–2201.
13. Grandfield J. F., Davidson C. J., Taylor J. A. Light Metals. Ed. by J. L. Anjier 2001. Warrendal, 2001. pp. 911–916.
14. Evans J. W. The use of electromagnetic casting for AI alloys and other metals. JOM. 1995. Vol. 47. pp. 38–41.
15. Yu-bo Zuo, Jian-zhong Cui, Dan Mou, Qing-feng Zhu, Xiang-jie Wang, Lei Li. Effect of electromagnetic field on microstructure and macrosegregation of flat ingot of 2524 aluminium alloy. Transactions of Nonferrous Metals Society of China. 2014. Vol. 2. pp. 132–134.
16. Pervukhin M. V., Sergeev N. V. Design of electromagnetic crystallizer parameters to ensure stable ingot formation in magnetic field. Vestnik of Samara State Technical University. Technical Sciences Series. 2010. No. 2 (26). pp. 153–161.
17. Pervukhin M. V., Figurovskiy D. K., Romanova E. V. Formation of structure in the Аl – Се alloy under electromagnetic crystallization. Tekhnologiya legkikh splavov. 2010. No. 2. pp. 71–76.
18. GOST 21073.1–75. Non-ferrous metals. Determination of grain size by comparison with microstructure scale (incl. Revision 1). Introduced: 01.07.1976.
19. OST 1 34076–85. Pan head rivets. Introduced: 01.07.1986.
20. GOST 14838–78. Wire of alluminium and alluminium alloys for cold upsetting. Specifications (incl. Revisions 1, 2, 3, 4). Introduced: 01.01.1979.

Language of full-text russian
Full content Buy
Back