Журналы →  Eurasian Mining →  2019 →  №2 →  Назад

EQUIPMENT AND MATERIALS
Название Design and industrial testing of innovative nonexpendable picks for cutter-loaders
DOI 10.17580/em.2019.02.13
Автор Sementsov V. V., Prokopenko S. A., Ludzish V. S., Abramov V. V.
Информация об авторе

VostNII Science Center, Kemerovo, Russia:

Sementsov V. V., Head of Laboratory, Candidate of Engineering Sciences
Ludzish V. S., Professor, Doctor of Engineering Sciences

National Research Tomsk Polytechnic University, Tomsk, Russia:

Prokopenko S. A., Professor, Doctor of Engineering Sciences, sibgp@mail.ru


KemRIPK—Kemerovo Regional Institute for Advanced Training, Kemerovo, Russia:

Abramov V. V., Professor, Doctor of Engineering Sciences

Реферат

The tendency of increasing dimensions of cutter–loader picks results in many departures of the machine from face area during rock breaking in mines. This is governed by the current structure of the tangential rotary picks making their repair and second use impossible. The studies of the mechanisms and degree of the pick wear yield the proposal of the new design aimed at essential extension of life time of the rock-breaking tool. In the developed split pick design, up to 80% of the tool is usable many times. The working part subjected to abrasive wear and making 20% of the pick weight and length is replaceable after wear of the tungsten carbide nose. The experimental pilot picks of the spit design were tested in cutting coal (with adjacent rocks with hardness f = 5–6) in a Kuzbass mine in December 2017. The tests proved availability and repairability of the proposed design. No detachment of the replaceable heads from their shank ends was observed. During the tests, the cutter–loader broke 7500 t of rocks. The picks underwent 4–5 replacements of the wornout heads while preserving their shape and workability.

The article is prepared in the framework of the Competitiveness Enhancement Program of the Tomsk Polytechnic University.

Ключевые слова Mine, cutter–loader, split pick, structure, head, test, wear, innovation
Библиографический список

1. Sidorenko A. A., Sishchuk J. M., Gerasimova I. G. Underground mining of multiple coal seams: Problems and solutions. Eurasian Mining. 2016. No. 2. рр. 11–15. DOI: 10.17580/em.2016.02.03
2. Prokopenko S. A. From underground coal mining—to the coalpower complexes. Gornyi Zhurnal. 2005. No. 11. pр. 8–10.
3. Yutyaev E. P. Current challenges and development prospects for underground mining of flat gas-bearing coal seams. Ugol. 2017. No. 5. pp. 30–36.
4. Plakitkin Yu. A., Plakitkina L. S. The Industry 4.0 global innovation project’s potential for the coal industry of Russia. 1. The Industry 4.0 program—new approaches and solutions. Ugol. 2017. No. 10. pp. 44–50.
5. Cheluzska P. Computer–aided design of robotised technology for manufacturing working units of mining machines. International Journal of Mining, Reclamation and Environment. 2015. Vol. 29(1). рp. 62–81.
6. Prokopenko S. A., Kurzina I. A., Lesin Yu. V. Prospects for improvement of mining machines’ cutting picks. IOP Conference Series: Materials Science and Engineering. 2016. Vol. 124(1). рp. 1–5. DOI: 10.1088/1757-899X/124/1/012134
7. Klishin V. I., Gerike B. L., Nikitenko S. M., Krestovozdvizhensky P. D. Types and causes of failure of tangential-rotary cutter bits. Gornyi Zhurnal. 2016. № 7. рр. 92–95. DOI: 10.17580/gzh.2016.07.20
8. Bolobov V. I., Bobrov V. L., Talerov M. P., Bochkov V. S. Cause rapid wear tangential cutters. Proceedings of the Mining Institute. St. Petersburg, 2012. Vol. 195. pp. 238–240.
9. Kotwica K. Results of laboratory investigations into operating conditions of cutting tool. Journal of Mining Science. 2003. Vol. 39(2). pp. 168–173.
10. Liu X., Liu S., Li L., Cui X. Experiment on conical pick cutting rock material assisted with front and rear water jet. Advances in Materials Science and Engineering. 2015. Vol. 2015. ID 506579. DOI: 10.1155/2015/506579
11. Krestovozdvizhensky P. D., Klishin V. I., Nikitenko S. M., Gerike P. B. Selecting shape of reinforcement insertions for tangential swivel cutters of mining machines. Journal of Mining Science. 2015. Vol. 51(2). pp. 323–329.
12. Dvornikov L. T., Korneyev V. A., Korneyev P. A., Krestovozdvizhensky P. D., Nikitenko S. M. Main development trends and some technical decisions on mining tools equipped with super-hard composite materials inserts. IOP Conference Series: Earth and Environmental Science. 2017. 012031. DOI: 10.1088/1755-1315/53/1/012031
13. Prokopenko S. A., Ludzish V. S., Kurzina I. A. Design of newclass picks for cutter–loaders. Gornyi Zhurnal. 2017. No. 2, pp. 75–78. DOI: 10.17580/gzh.2017.02.14
14. Chinakhov D. A Study of thermal cycle and cooling rate of steel 30HGSA single-pass weld joints. Applied Mechanics and Materials. 2011. No. 52–54. рp. 442–447.
15. Surface miner cutting tools. Available at: http://mining.sandvik.com/en/products/tools/surface-miner/surface-minercutting-tools (accessed: 30.11.2017).
16. Kennametal value business system. Kennametal catalog 2006. 38 p.
17. Moshkin N. V., Kalinin V. V. Tool contributing to higher productivity. Ugol. 2006. No. 8. pp. 46–47.
18. Gao K. D., Du C. L., Jiang H. X. et al. A theoretical model for predicting the peak cutting force of conical picks. Fratt Integr Strutt. 2014. No. 8. рр. 43–52.
19. Kim E., Rostami J., Swope C., et al. Study of conical bit rotation using full-scale rotary cutting experiments. Journal of Mining Science. 2012. No. 48. рр. 717–731.
20. Kim E. Effect of skew angle on main precursor of frictional ignition in bench-scale simulation of excavation processes. International Journal of Rock Mechanics & Mining Sciences. 2015. No. 80. рр. 101–106.
21. Fu L., Du C. L., Li J., Zheng K. Influence of pick working angle on cutting performance of auger miner’s aiguille. Advances in Mechanical Engineering. 2015. Vol. 7(5). pp. 1–10. DOI: 10.1177/1687814015585427.
22. Shabaev O. E., Semenchenko A. K., Khitsenko N. V., Stadnik N. I. Experimental studies into the operating modes of cutter–loader drum. Gornoe oborudovanie i elektromekhanika. 2010. No. 10. pp. 49–56.
23. Mamet’ev L. E., Khoreshok A. A., Tsekhin A. M., Borisov A. Y. Stress distribution in attachments of disc cutters in heading drivage. Journal of Mining Science. 2015. Vol. 51, No. 6. pp. 1150–1156.

Полный текст статьи Design and industrial testing of innovative nonexpendable picks for cutter-loaders
Назад