Journals →  CIS Iron and Steel Review →  2020 →  #2 →  Back

Environment protection
ArticleName Titanium-containing coagulants for foundry wastewater treatment
DOI 10.17580/cisisr.2020.02.14
ArticleAuthor E. N. Kuzin, N. E. Kruchinina
ArticleAuthorData

D. Mendeleyev University of Chemical Technology of Russia (Moscow, Russia):

E. N. Kuzin, Cand. Eng., Department of Environmental Engineering, E-mail: e.n.kuzin@mail.ru

N. E. Kruchinina, Dr. Eng., Head of Faculty of Biotechnology and Environmental Engineering, Head of Department of Environmental Engineering, E-mail: krutch@muctr.ru

Abstract

Setting up a circulation water supply system is a prerequisite for a modern competitive steel making company. The most frequent problem faced by steel makers includes the challenge of removing suspended solids from large volumes of wastewater. Residual concentration of suspended solids (1-10 mg/l) is the main criterion of treatment efficiency. The most difficult task is to remove particles smaller than 1-2 microns, which stay suspended for a long time. One of the biggest sources of wastewater includes the process of removing residual molding sand from machine parts by water jet surface cleaning. Apart from high concentrations of suspended solids, process wastewater have high concentrations of dissolved organic compounds and require prior treatment before it can go to municipal wastewater treatment plants. Titanium-containing coagulants are being used more and more commonly in water treatment processes due to their high efficiency and the lack of most of the drawbacks inherent in conventional coagulants. This paper compares the conventional coagulants (i.e. aluminum and iron compounds) and coagulants containing titanium salts. In addition, complex titanium-containing coagulants were tested in the actual process of removing residual molding sand from machine parts by water jet surface cleaning. The findings show that titanium tetrachloride outperforms the conventionally used aluminum sulphate and iron chloride, while the effective dose of titanium tetrachloride is on average 2.5 to 3.0 times smaller. The obtained experimental data characterize the effect of added titanium compounds on the water treatment efficiency when conventional reagents are used. It was found that the addition 7.5 wt% of titanium tetrachloride to the conventional aluminum sulphate increases the treatment performance of the latter by 30%. The high efficiency of titanium-containing reagents is due to specific hydrolysis effects, as well as nucleation and flocculation at the surface of hydrolysis products. The rate of sedimentation and filtration of sludges resultant from water treatment with titanium-containing coagulants significantly exceeded that reached when using conventional reagents. The use of titanium-containing reagents will enable to transfer to smaller settlers and filters, reduce the consumption of reagents and reach an enhanced treatment performance. The treated water can be reused or discharged into municipal sewage treatment plants.

This research study was carried out as part of the programme supporting research projects carried out by young staff of D. Mendeleev University of Chemical Technology of Russia (Application З-2020-013)

keywords Coagulation, titaniumcontaining coagulants, suspended solids, water jet cleaning of parts
References

1. Zhukovskiy S. S., Lyass A. M. Moulds and cores made of coldsetting sands. Moscow : Mashinostroenie, 1978. 224 p.
2. Gerasimov S. P., Titov A. Yu., Palachev V. A., Konovalov A. N. Technology of art casting obtaining using cold-setting mixture molds with facing ceramic layer. Tsvetnye Metally. 2015. No. 10. pp. 8–12.
3. Illarionov I. E. A scientific basis for developing core and molding sands with the help of inorganic phosphate binders and hardener powders. Liteyshchik Rossii. 2016. No. 1. pp. 16–27.
4. Evlampiev A. A., Chernyshev E. A., Grigoriev L. P. The practice of adopting the Alfa-set process. Liteynoe proizvodstvo. 2011. No. 5. pp. 17–18.

5. Lyutyi R. V., Guriya I. M., Shapovalova D. V., Keush D. V. Orthophosphoric acid and metal salts contained in molding sands as the basis for binder formation. Liteynoe proizvodstvo. 2013. No. 5. pp. 16–19.
6. Golovin K. A., Grigoryev G. V., Grigoryeva E. N., Pushkarev A. E. Selecting and substantiating parameters for erosion of materials by high-velocity jet. Gornyy informatsionno-analiticheskiy byulleten. 2004. No. 2. pp. 261–264.
7. Bagazeev V. K., Valiev N. G., Simisinov D. I. Physico-mechanical substantiation of rock mass jetting in hydraulic borehole mining of placers. Gornyi Zhurnal. 2015. No. 12. pp. 25–27. DOI 10.17580/gzh.2015.12.05.
8. Brenner V. A., Zhabin A. B., Shchegolevskiy M. M., Polyakov Al. V., Polyakov An. V. Optimization of water jetting techniques for mining industry. Moscow : Gornaya kniga, 2010. 343 p.
9. Matinde E., Simate G. S., Ndlovu S. Mining and metallurgical wastes: A review of recycling and re-use practices. Journal of the Southern African Institute of Mining and Metallurgy. 2018, Vol. 118. pp. 825–844.
10. Young C. A. SME Mineral Processing and Extractive Metallurgy Handbook. Society for Mining, Metallurgy & Exploration. 2019. 2312 p.
11. Ventskel A. V., Kibirev V. I., Kuznetsov A. Yu., Turyanskiy B. V. Optimization of the circulation water supply system at Karelsky Okatysh OJSC. Obogashchenie Rud. 2008. No. 2. pp. 35–37.
12. Prakash N. B., Vimala S., Jayakaran P. Waste water treatment by coagulation and flocculation. International Journal of Engineering Science and Innovative Technology. 2014. Vol. 3. pp. 479–484.
13. Jahanshahi M., Taghizadeh M. M. Pre-sedimentation tank effects on water treatment unit operation. Environmental quality. 2018. Vol. 28. pp. 35–42.
14. Draginskiy V. L., Alekseeva L. P., Getmantsev S. V. Natural water treatment methods and coagulation. Moscow : Nauchnoe izdatelstvo. 2005. 576 p.
15. Galloux J., Chekli L., Phuntsho S., Tijing L. D., Jeong S., Zhao Y. X., Gao B. Y., Park S. H., Shon H. K. Coagulation performance and floc characteristics of polytitanium tetrachloride and titanium tetrachloride compared with ferric chloride for coal mining wastewater treatment. Separation and Purification Technology. 2015. No. 152. pp. 94–100. DOI: 10.1016/j.seppur.2015.08.009.
16. Zhao Y., Phuntsho S., Gao B. et al. Preparation and Characterization of Novel Polytitanium Tetrachloride Coagulant for Water Purification. Environmental Science & Technology. 2013. Vol. 47. pp. 12966–12975. DOI: 10.1021/es402708v.
17. Zhao Y. X., Gao B. Y., Zhang G. Z., Qi Q. B., Wang Y., Phuntsho S., Kim J.-H., Shon H. K., Yue Q. Y., Li Q. Coagulation and sludge recovery using titanium tetrachloride as coagulant for real water treatment: A comparison against traditional aluminum and iron salts. Separation and Purification Technology. 2014. Vol. 130. pp. 19–27. DOI: 10.1016/j.seppur.2014.04.015.
18. Kyeong-Jun Jeon, Johng-Hwa Ahn. Evaluation of titanium tetrachloride and polytitanium tetrachloride to remove phosphorus from wastewater. Separation and Purification Technology. 2018. Vol. 197. pp. 197–201.
19. Zhao Y., Gao B., Shon H. Floc characteristics of titanium tetrachloride (TiCl4) compared with aluminum and iron saltsin humic acid–kaolin synthetic water treatment. Separation and Purification Technology. 2011. Vol. 81. pp. 332–338. DOI: 10.1016/j.seppur.2014.12.043.
20. Kuzin E. N., Averina Yu. M., Kurbatov A. Yu., Sakharov P. A. Wastewater treatment in the electroplating industry using composite coagulants-reducers. Tsvetnye Metally. Moscow, 2019. No. 10. pp. 91–96.
21. Shabanova N. A., Popov V. V., Sarkisov P. D. The chemistry and technology of nanodispersed oxides. Learner’s guide. Moscow : IKTs “Akademkniga”. 2007. 309 p.
22. Izmaylova N. L., Lorentsson A. V. Understanding the hydrolysis of diluted aqueous solutions of ТiOSO4·2Н2О and TiCl4 and electrosurface properties of the hydrolysis products. Proceedings of the 6th Russian National Conference among Young Researchers and Post- and Undergraduate Students with International Participants “Mendeleev-2012”. Saint Petersburg : Izdatelstvo Solo, 2012. pp. 205–207.
23. Wang T.-H., Navarrete-López A. M., Li S., Dixon D. A., Gole J. L. Hydrolysis of TiCl4: Initial steps in the production of TiO2. Journal of Physical Chemistry A. 2010. Vol. 114 (28). pp. 7561–7570. DOI: 10.1021/jp102020h.
24. Shon H., Vigneswaran S., Kandasamy J., Zareie M., Kim J., Cho D., Kim J. H. Preparation and characterization of titanium dioxide (TiO2) from sludge produced by TiCl4 flocculation with FeCl3, Al2(SO4)3 and Ca(OH)2 coagulantaids in wastewater. Separation Science and Technology. 2009. 44. pp. 1525–1543. DOI: 10.1080/01496390902775810.
25. Shon H., Vigneswaran S., Kim I.S. Preparation of Titanium Dioxide (TiO2) from Sludge Produced by Titanium Tetrachloride (TiCl4) Flocculation of Wastewater. Environmental Science & Technology. 2007. Vol. 41. pp. 1372–1377. DOI: 10.1021/es062062g.
26. Butorina I. V., Butorina M. V. Issues of implementing the best available technologies in the steel industry of the Russian Federation. Chernye Metally. 2019. No. 1. pp. 43–48.
27. Kolesnikov A. V., Savelyev D. S., Kolesnikov V. A., Dadydkova T. V. Extraction of highly dispersed titanium dioxide TiO2 from aqueous electrolyte solutions by electroflotation. Steklo i keramika. 2018. No. 6. pp. 32–36.

Full content Titanium-containing coagulants for foundry wastewater treatment
Back