Journals →  Chernye Metally →  2021 →  #10 →  Back

65th anniversary of Lipetsk State Technical University
ArticleName Development of mathematical models for formation of the cross profile of strips during hot rolling, taking into account the wear of rolls
DOI 10.17580/chm.2021.10.02
ArticleAuthor V. A. Pimenov, D. A. Kovalev, M. A. Dagman, I. P. Mazur.
ArticleAuthorData

Novolipetsk Metallurgical Plant (Lipetsk, Russia):

V. A. Pimenov, Cand. Eng., Senior Researcher, Chief Specialist, e-mail: pimenov_va@nlmk.com
D. A. Kovalev, Cand. Eng., Acting Director of Directorate for Development of NewTechnologies, e-mail: kovalev_da@nlmk.com
M. A. Dagman, Specialist, Rolling Production Directorate

 

Lipetsk State Technical University (Lipetsk, Russia)
I. P. Mazur, Dr. Eng., Prof., Head of Metal Forming Dept., e-mail: mazur@stu.lipetsk.ru

Abstract

On the basis of the physical laws of the rolling process, an integrated mathematical model of the formation of the cross profile of a hot-rolled strip on a broad-strip mill was built, including models of the grinding profile of rolls with axial shift, bending of rolls, elastic flattening in contact with the strip, thermal expansion of the barrel, and wear of the work rolls surface during rolling. When predicting the wear of rolls, the uneven pressures in contact with the strip were taken into account using a generalized model and the displacement of the strip along the length relative to the mill axis using a stochastic model. The adaptation of the wear model according to the experimental data based on the comparison of the predicted and measured wear of rolls after rolling is carried out and the adequacy of the developed integrated model of profile formation is shown. This model was used on the 2000 broadband mill to improve the hot rolling technology and optimize the planning of assembly batches, primarily in the production of large volumes of rolled electrical steels with high requirements for the accuracy of the cross section. Proposals are formulated for the development of criteria for optimizing hot rolling technology according to the characteristics of the cross section, which ensure metal savings, increase the broadband mill productivity, and maximize consumer properties.

keywords Hot rolling, mathematical modeling, strip cross-section, work rolls, thermal field, elastic flattening, wear, adaptation, optimization
References

1. Pimenov V. A., Dagman A. I., Kovalev D. A. Analysis and mathematical simulation of formation regularities of strip transversal profile during hot rolling. Steel in translation. 2020. Vol. 50. No. 2. pp. 107–111.
2. Nikolaev V. А., Roberov I. G. Calculation of the work rolls deflection taking into account the unevenness of linear contact forces. Proizvodstvo prokata. 2019. No. 12. pp. 9–14.
3. Elsgolts L. E. Differential equations and variational calculus. Moscow: Editorial URSS, 2000. pp. 161–165.
4. Timoshenko S. P., Goodier J. N. Theory of Elasticity. Moscow: Nauka, 1979. 560 p.
5. Carlslaw H. S., Jaeger J.C. Conduction of heat in solids. Moscow: Nauka, 1964. 488 p.
6. John S., Sikdar S., Mukhopadhyay A., Pandit A. Roll wear prediction model for finishing stands of hot strip mill. Ironmaking and Steelmaking. 2006. Vol. 33. No. 2. pp. 169–175.
7. Ziying Liu, Yingping Guan, Fengqin Wang. Model development of work roll wear in hot strip mill. Materials Science and Engineering. 2017. Vol. 207. pp. 1–4.
8. Eghtesad M., Aliakbarian M., Rasouli M. Study of friction and rolls wear in hot strip mill of mobarakeh steel company. International Journal of Theoretical and Applied Sciences. 2016. No. 8. Iss. 2. pp. 6–16.
9. Ginzburg V. Steel-rolling technology: theory and practice. New York: Marcel Dekker, 1989. 791 p.
10. Yanlin Li, Jianguo Cao, Lan Qui et al. Effect of strip edge drop of electrical steel on profile and flatness during hot rolling process. Advanced in Mechanical Engineering. 2019. Vol. 11. pp. 1–11.
11. Pimenov V. A., Pertseva V. S. Developing methods of analyzing and evaluating the accuracy of the cross section of a hot-rolled product. Metallurgist. 2015. Vol. 58. No. 9–10. pp. 770–776.
12. Shatalov R. L., Grigoryan G. G., Sharov А. А., Savin V. А. Development of the structure and construction of a regression model of the wear of sheet mill work rolls. Izvestiya vuzov. Chernaya metallurgiya. 1987. No. 9. pp. 59–65.
13. Hattori H., Oda N., Маеdа N. New type of HSS work roll for later stands in hot strip mill finishing trains. Chernye Metally. 2014. No. 8. pp. 33–38.
14. Shatalov R. L. Control of strip quality and deformability in rolling. Steel in Translation. 2004. Vol. 34. Iss. 9. pp. 43–47.

Language of full-text russian
Full content Buy
Back