Journals →  CIS Iron and Steel Review →  2023 →  #1 →  Back

Corrosion, Metal Protection and Heat Insulation
ArticleName Parameters of protective carbon films applied on high-speed steels M42 via magnetronic sputtering
DOI 10.17580/cisisr.2023.01.17
ArticleAuthor A. E. Litvinov, V. Yu. Buzko, S. N. Ivanin, E. Yu. O. Balaev
ArticleAuthorData

Kuban State Technological University (Krasnodar, Russia):

A. E. Litvinov, Dr. Eng., Associate Prof., Head of the Dept., e-mail: artstyleone@mail.ru

E. Yu. O. Balaev, Senior Lecturer, e-mail: balaev1122@mail.ru

 

Kuban State Technological University (Krasnodar, Russia)1 ; Kuban State University (Krasnodar, Russia)2:

V. Yu. Buzko, Cand. Chem., Associate Prof., Director of the Center for Advanced Technologies and Nanomaterials1,2
S. N. Ivanin, Cand. Chem., Researcher, Center for Advanced Technologies and Nanomaterials1,2

Abstract

High-speed steel M42, which is used as material for saw teeth in the most popular bimetallic saws, is considered as one of the most universal high-speed steel grades. This steel is characterized by high hardness (HRC 64-67), excellent heat resistance up to 700 °C, good wear resistance and is suitable for cutting of stainless steels with hardness up to 50 HRC. Nanostructured wear-resistant high-hard coatings with high physical and mechanical properties, resistance to impact and vibration loads promotes increase of wear resistance and service life of band saws. The films of hard diamondlike carbon (DLC), containing amorphous carbon with disordered graphite ordering, which is striving to a tetrahedral diamond-like coordination, are interesting for material scientists due to their excellent mechanical and tribological properties. Dense and hard carbon films with structure of nanoparticles having size 12-17 nm, were applied on highspeed steel M42 (according to AISI) via the method of high-frequency magnetronic sputtering. Microhardness of DLC film of high-speed steel M42 (M42 HSS) by Vickers with the coating thickness 800 nm was 838±19 in comparison with 783±18 for a clean sample of the same steel. Good microstructure, wear protection properties and high temperature oxidation protection of obtained carbon nanostructured films on the surface of M42 HSS are observed.

The research was conducted under support of the Council of grants of RF President (Agreement No. MD-2727.2022.4).

keywords Magnetronic sputtering, wear, high-temperature protection, coating, nanostructured films, high-speed steel
References

1. Balaev E. Yu., Litvinov А. E. Analysis of modern technologies for improving performance characteristics of cutting band saws. Advances in Engineering Research. 2018. Vol. 158. pp. 259-263.
2. Khan F. N., Daadbin A., Persson M., Haider J., Hellbergh H. Assessing the performance of TiAlSiN coating on bandsaw tooth when cutting Ti-17 alloy. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. 2012. Vol. 226. pp. 870-877.
3. Litvinov A. E., Buzko V. U., Balaev E. Yu., Goryachko A. I. Development of a method of applying nanostructured and wearresistant coatings with high adhesion to the surface of the cutting tool. IOP Conf. Series: Materials Science and Engineering. 2019. No. 560. 012187.
4. Robertson J. Diamond-like amorphous carbon. Materials Science and Engineering: R: Reports. 2002. Vol. 37. No. 4–6. pp. 129-281.
5. Ohtake N., Hiratsuka M., Kanda K., Akasaka H., Tsujioka M., Hirakuri K., Hirata A., Ohana T., Inaba H., Kano M., Saitoh H. H. Properties and Classification of Diamond-Like Carbon Films. Materials. 2021, Vol. 14, 315. DOI: 10.3390/ma14020315
6. Xue Y. J., Zhang Y. Z. Surface coatings in tribological and wearresistant applications. International Heat Treatment and Surface Engineering. 2009. Vol. 3. No. 1/2. pp. 17-25.
7. Rother B., Herrmann U., Schulze S. Wear resistant carbon coatings deposited without substrate bias voltage. Thin Solid Films. 2001. No. 398–399. pp. 187–192.
8. Kahn M., Menegazzo N., Mizaikoff B., Berghauser R., Lackner J. M., Hufnagel D., Waldhauser W. Properties of DLC & Nitrogen-Doped DLC Films Deposited by DC Magnetron Sputtering. Plasma Process. Polym. 2007. No. 4. S200–S204.
9. Zhang S., Bui X. L., Fu Y. Magnetron sputtered hard a-C coatings of very high toughness. Surface and Coatings Technology. 2003. Vol. 167. pp. 137–142. DOI: 10.1016/S0257-8972(02)00900-3
10. Lin C. R., Wei D. H., Chang C. K., Liao W. H. Optical Properties of Diamond-like Carbon Films for Antireflection Coating by RF Magnetron Sputtering Method. Physics Procedia. 2011. Vol. 18. pp. 46–50.
11. Mróz W., Burdynska S., Prokopiuk A., Jedynski M., Budner B., Korwin-Pawlowski M. L. Characteristics of Carbon Films Deposited by Magnetron Sputtering. Acta Physica Polonica A. 2009. Vol. 116. pp. 120–122.
12. Abbass A. A., Kadhem S. J. Preparation and characterization DLC thin films using atmospheric pressure plasma Jet. IOP Conf. Ser.: Mater. Sci. Eng. 2018. Vol. 454. 012065.
13. Potapov A. A., Bulavkin V. V., German V. A., Vyacheslavova O. F. Study of micro-relief of processed surfaces using the method of fractal signatures. Zhurnal tekhnicheskoy fiziki. 2005. Vol. 75. Iss. 5. pp. 28-45.
14. Zhou X. L., Suzuki T., Nakajima H., Komatsu K., Kanda K., Ito H., Saitoh H. Structural analysis of amorphous carbon films by spectroscopic ellipsometry, RBS/ERDA, and NEXAFS. Applied Physics Letters. 2017. Vol. 110. 201902.
15. Dai H. Y., Cheng X. R., Wang C. F., Xue Y. C., Chen Z. P. Structural, optical and electrical properties of amorphous carbon films deposited by pulsed unbalanced magnetron sputtering. Optik. 2015. Vol. 126. pp. 861–864.
16. Jo H. J., King J. L., Blomstrand K., Sridharan K. Spectral emissivity of oxidized and roughened metal surfaces. International Journal of Heat and Mass Transfer. 2017. Vol. 115. Part B. pp. 1065–1071.
17. King J. L., Jo H., Tirawat R., Blomstrand K., Sridharan K. Effects of Surface Roughness, Oxidation, and Temperature on the Emissivity of Reactor Pressure Vessel Alloys. Nuclear Technology. 2017. Vol. 200. No. 1. pp. 1–14.
18. Erdemir A., Bindal C., Pagan J., Wilbur P. Characterization of transfer layers on steel surfaces sliding against diamond-like hydrocarbon films in dry nitrogen. Surface and Coatings Technology. 1995. Vol. 76. pp. 559–563.
19. Chen F., Chen J., Zhou H., Li C. DLC Films Synthesized on the Ti6Al4V alloy surface by Plasma Gun at an Atmospheric Pressure. Materials Science Forum. 2011. Vol. 687. pp. 739–744.
20. Lijun Wang, Yan Liu, Hui Chen, Mengchao Wang. Modification Methods of Diamond like Carbon Coating and the Performance in Machining Applications: A Review. Coatings. 2022. Vol. 12. 224.
21. Qunfeng Zeng, Zekun Ning. High-temperature tribological properties of diamond-like carbon films: A review. Reviews on Advanced Materials Science. 2021. Vol. 60. p. 276–292
22. Haruyo Fukui, Junya Okida, Naoya Omori, Hideki Moriguchi, Keiichi Tsuda. Cutting performance of DLC coated tools in dry machining aluminum alloys. Surface & Coatings Technology. 2004. Vol. 187. pp. 70–76.
23. Tobola D., Liskiewicz T., Liuquan Yang, Thawhid Khan, Boron L. Effect of mechanical and thermochemical tool steel substrate pre-treatment on diamond-like carbon (DLC) coating durability. Surface and Coatings Technology. 2021. Vol. 422. 127483.
24. dos Santos G. R., da Costa D. D., Amorim F. L., Torres R. D. Characterization of DLC thin film and evaluation of machining forces using coated inserts in turning of Al–Si alloys. Surface & Coatings Technology. 2007. Vol. 202. pp. 1029–1033.
25. Folea M., Roman A., Lupulescu N.-B. An overview of dlc coatings on cutting tools performance. Academic Journal of Manufacturing Engineering. 2010. Vol. 8. No. 3. pp. 30-36.

Full content Parameters of protective carbon films applied on high-speed steels M42 via magnetronic sputtering
Back