Journals →  Chernye Metally →  2014 →  #6 →  Back

Development of metallurgy in Russia and CIS
ArticleName Deformation regularities of an external layer of bimetal rod ends at the initial stage of cold direct extrusion
ArticleAuthor M. P. Baryshnikov, E. B. Medvedev
ArticleAuthorData

Magnitogorsk State Technical University (Magnitogorsk, Russia):

Baryshnikov M. P., Cand. Eng., Ass. Prof., Chair of Mechanical and Metallurgical Process Engineering

 

Ufa State Aviation Technical University (Ufa, Russia):

Medvedev E. B., Cand. Eng., Ass. Prof., Chair of Nanotechnologies
E-mail (common): arcosmag@mail.ru

Abstract

Change of the thickness of an outer layer of a bimetal rod end produced by direct cold extrusion of cross-layered bimetal ingots has been investigated. Such rods are applied to produce bimetal sparkplug center electrodes for combustion engines. The change of the outer layer thickness of a round bimetal rod end was studied at the initial (non-steady) stage of direct cold extrusion depending on the change of the sizes of an initial round bimetal rod (thickness of a bottom layer of a billet). The deformation process at the initial stage is studied due to the fact that initial cross-layered billets used for manufacturing of bimetal billets usually have a small relative thickness of the bottom layer, which often results in final formation of designed dimensions of rods and relative service properties of rods at the initial stage. The investigation results allow stating that the character of change of an outer layer thickness of a round bimetal rod end at the initial stage of direct extrusion depending on the thickness of a bottom layer of an initial bimetal billet can be approximately described by a parabolic relation. It is demonstrated that an external layer with a thickness smaller than that of the lower cross layer of the initial billet at certain values of the thickness of the bottom cross layer of the initial billet. This can be considered the peculiarity of the process under consideration.

keywords Cross-layered bimetal billet, bimetal rod, bottom layer of a billet, external layer of a rod end, rod end, initial and main stages of direct extrusion
References

1. Perlin I. L., Raytbarg L. Kh. Teoriya pressovaniya metallov (Theory of metal pressing). Moscow : Metallurgiya, 1975. 448 p.
2. Zholobov V. V., Zverev G. I. Pressovanie metallov (Metal pressing). Moscow : Metallurgiya, 1971. 455 p.
3. Moguchiy L. N. Obrabotka davleniem trudnoob rabatyvaemykh materialov (Forming operation of hard-processing materials). Moscow : Mashinostroenie, 1976. 272 p.
4. Kovka i shtampovka : spravochnik v chetyrekh tomakh. Tom 3: Kholodnaya obemnaya shtampovka (Forging and stamping : reference book in four volumes. Volume 3: Cold forging). Under the editorship of G. A. Navrotskiy. Moscow : Mashinostroenie, 1987. 384 p.
5. Bass B. A. Svechi zazhiganiya: kratkiy spravochnik (Spark-plugs: brief reference book). Moscow : Za rulem, 2002. 120 p.
6. Medvedev E. B., Shuster L. Sh. Dvigateli vnutrennego sgoraniya. Vseukrainskiy nauchno-tekhnicheskiy zhurnal — Internal Combustion Engines. All-Ukrainian scientifi c and technical journal. 2009. No. 2. pp. 86–90.
7. Medvedev E. B., Abramov A. N., Medvedev A. E. Kuznechno-shtampovochnoe proizvodstvo — Die forging. 2008. No. 12. pp. 43–47.
8. Medvedev E. B., Baryshnikov M. P. Vestnik Magnitogorskogo gosudarstvennogo tekhnicheskogo universiteta imeni G. I. Nosova — Bulletin of Magnitogorsk State Technical University named after G. I. Nosov. 2010. No. 3. pp. 28–32.
9. Medvedev E. B., Shuster L. Sh., Baryshnikov M. P. Issledovanie i razrabotka rotornoy tekhnologii izgotovleniya svechey zazhiganiya dvigateley vnutrennego sgoraniya (Research and development of rotary technology of manufacturing of spark plugs of internal combustion engines). Metody povysheniya tekhnologicheskikh vozmozhnostey metalloobrabatyvayushchego oborudovaniya s chislovym programnym upravleniem : mezhvuzovskiy sbornik nauchnykh trudov (Methods of increasing of technological possibilities of metal processing equipment with computer numerical control : inter-university collection of scientifi c proceedings). Publishing House of Ufa State aviation University, 2010. pp. 75–82.
10. Tretyakov A. V., Zyuzin V. I. Mekhanicheskie svoystva metallov i splavov pri obrabotke davleniem (Mechanical properties of metals and alloys in the time of forming operation). Second eddition. Moscow : Metallurgiya, 1973. 224 p.

Language of full-text russian
Full content Buy
Back