Author 1:
Name & Surname: Linnik Yu. N.
Company: State University of Management (Moscow, Russia)
Work Position: Professor
Scientific Degree: Doctor of Engineering Sciences
Contacts: yn_linnik@guu.ru

Author 2:
Name & Surname: Sherstkin V. V.
Company: State University of Management (Moscow, Russia)
Work Position: Assistant Professor
Scientific Degree: Candidate of Engineering Sciences

Author 3:
Name & Surname: Linnik V. Yu.
Company: State University of Management (Moscow, Russia)
Work Position: Professor
Scientific Degree: Doctor of Economical Sciences

The integral index of coal breakability is currently accepted as its cuttability which is a weighted mean value of cuttability of coal, dirt bands and hard mineral inclusions but it is weakly reflective of presence of hard mineral inclusions and hard dirt bands that to a great extent condition dynamic characteristics of coal cutting as well as reliability and productiveness of coal cutter-loaders. Ignoring properties of inhomogeneities in coal results in considerably inaccurate choice of coal cutting machine performance, especially in complex structure seams. In connection with this, a problem was formulated such that its solution would, on the one hand, allow estimating coal cutting machine conditions not by a set of characteristics but by an integral criterion perceptive of hard inhomogeneities in coal and, on the other hand, permit using this index in calculating performance and productivity of coal cutter-loaders and production data of coal faces and coal mines. The article describes studies into strength characteristics and geological structure of coal seams (cuttability of coal, interbeds and hard inclusions, specific content of hard inclusions per coal seams). By the results of the studies and based on the physical views on influence exerted by these characteristics on serviceability and life of cutting tools, the authors put forward an integral criterion of coal breakability—equivalent cuttability index Аe. In the capacity of a reliability criterion for cutting tool, the authors assume failure rate—the value that is inverse to basic overhaul time. The practical importance of Аe is its ability to estimate operating conditions of a cutter–loader not with a set of characteristics but with an integral critertion, considering presence of hard heterogeneities in coal, first, and second, Аe is applcable in calculation algorithms for parameters of cutter–loaders, their output, serviceability, basic overhaul time and, on the whole, performance of production faces and coal mines.

1. Pozin E. Z., Melamed V. Z., Ton V. V. Razrushenie ugley vyemochnymi mashinami (Destruction of coals by stoping machines). Moscow : Nedra, 1984. 288 p.
2. Afanasiev V., Linnik V Information system development for the development forecasting of the raw-material base of coal industry. Special russian ugol (coal) magazine for world mining congress. Istanbul, 2011.
3. AfanasevV. Ya., Linnik Yu. N., Linnik V. Yu. Ugol Rossii: sostoyanie i perspektivy: monografiya (Russian coal: state and prospects: monograph). Moscow: INFRA-M, 2014. 271 p.
4. Zich A., Linnik Yu. N., Linnik V. Yu. Selecting Parameters of Cutter-Loader Lrums for Specific operating Conditions. Geo Resources Journal. Germany. 2015. No. 2. pp. 40–44.
5. Gorno-geologicheskie i kachestvennye kharakteristiki ugolnykh plastov (Mining-geological and qualitative characteristics of coal layers). Official registration certificate of the computer program No. 2012620451 (May 21, 2012). (in Russian).
6. Baron L. I. Gornotekhnicheskoe porodovedenie (Mining-technical rock study). Moscow : Nauka, 1977. 323 p.
7. Gorodnichenko V. I. Osnovy gornogo dela: uchebnik (Basis of mining: tutorial). V. I. Gorodnichenko, A. P. Dmitriev. Moscow : Moscow State Mining Institute, 2008.
8. Mineyev S. P., Rubinstiy A. A., Vitushko O. V., Radchenko A. G. Mining in difficult conditions in burst hazard strata. Donetsk: Skhidnyi vydavnychyi din, 2010. 606 p.
9. Hebel G., Hemmtr W., Lemmes F. Der Einsats vor Schramwalzen bei fallendem verhieb. Gluckauf. 1986. Vol. 122. No. 21.
10. Krashkin I. S., Linnik Yu. N., Braytsev A. V. Perspektivy razvitiya tekhnologii i tekhniki gornykh rabot na pologikh i naklonnykh plastakh shchakht Rossiyskoy Federatsii (Prospects of development of technology and technics of mining operations at flat-lying and edge seams of Russian mines). Nauchnye soobshcheniya Natsionalnogo nauchnogo tsentra gornogo proizvodstva (Scientific messages of National Scientific Center of Mining Production). Institute of Mining named after A. A. Skochinskiy. Moscow, 2005. Iss. 331. pp. 94-106.
11. Linnik Yu. N., Linnik V. Yu. Raschet parametrov ispolnitelnykh organov ochistnykh mashin na osnove elektronnogo banka dannykh o kharakteristikakh razrushaemosti ugolnykh plastov (Calculation of parameters of executors of scavenger floatation cells on the basis of electronic data bank about destruction characteristics of coal layers). Gornoe oborudovanie i elektromekhanika = Mining equipment and electromechanics. 2011. No. 2. pp. 42–50.
12. Kuntysh M. F., Baronskaya E.I. Metody otsenki svoystv ugolnykh plastov slozhnogo stroeniya (Methods of assessment of properties of complex coal layers). Moscow: Nauka, 1980. 142 p.
13. Baldin K. V. Teoriya veroyatnostey i matematicheskaya statistika (Probability theory and mathematical statistics). Moscow: Dashkov i Kо, 2010.
14. Gmurman V. E. Rukovodstvo k resheniyu zadach po teorii veroyatnostey i matematicheskoy statistike (Guidance for solving of issues of probability theory and mathematical statistics). Moscow: Vysshee obrazovanie, 2006.