Journals →  Non-ferrous Metals →  2015 →  #2 →  Back

METAL PROCESSING
ArticleName Selective laser melting of Ti – 6 Al – 4 V for gas turbine components manufacturing
DOI 10.17580/nfm.2015.02.04
ArticleAuthor Sufiiarov V. S., Popovich A. A., Borisov E. V., Polozov I. A.
ArticleAuthorData

Peter The Great Saint-Petersburg Polytechnic University, Saint-Petersburg, Russia:

V. S. Sufiiarov, Leading Researcher, e-mail: vadim.spbstu@ya.ru
A. A. Popovich, Professor, Head of Metallurgy, Mechanical Engineering and Transport Institute
E. V. Borisov, Researcher, Post Graduate Student
I. A. Polozov, Engineer, Student

Abstract

Additive manufacturing is a promising trend for production of metal products. They allow producing parts with complex configurations within a short time. The general principle of additive manufacturing technologies is producing of work pieces from CAD-files by adding material layer by layer. The usage of titanium alloys for manufacturing of parts for aviation industry by additive technologies is a promising direction. One of the most rapidly developing areas of additive manufacturing is the selective laser melting (SLM) of metallic powders. This paper presents the results of the powder Ti – 6 Al – 4 V alloy study, from which bulk samples and work pieces of turbomachine were made by SLM. Results of researching of microstructure and mechanical properties of bulk specimens before and after heat treatment are presented. The initial powder material consists of spherical particles with some satellites. Investigation of phase composition showed that particles are mainly composed of martensite α '-phase. Microstructure of the samples obtained by SLM indicated formation of martensite α '-phase in the form of fine-dispersed acicular precipitates formed because of high cooling rates. This microstructure explains high strength properties of samples before heat treatment (tensile strength 1160 MPa) and their low ductility (3.8%). Heat treatment resulted in partial destruction of martensite phase, thus increasing ductility (to 9.9%) and slightly reducing tensile strength (1090 MPa).

A. V. Grigorev — the Chief Designer of JSC “Klimov” — was also the participant of this work.

keywords Powder metallurgy, additive technology, additive manufacturing, selective laser melting, titanium-base alloy, Ti – 6 Al – 4 V.
References

1. Chester T. Sims, Norman S. Stoloff, William C. Hagel. Supersplavy II: Zharoprochnye materialy dlya aerokosmicheskikh i energeticheskikh ustanovok (Superalloys II: Heat-resistant materials for aerocosmic and energetic units). Moscow : Metallurgiya, 1995. 385 p.
2. Zlenko M. A., Popovich A. A., Mutylina I. N. Additivnye tekhnologii v mashinostroenii (Additive technologies in machine-building). Saint Petersburg : Publishing House of Polytechnical University, 2013. 222 p.
3. Sufiiarov V. Sh., Popovich A. A., Borisov E. V., Polozov I. A. Selektivnoe lazernoe plavlenie zharoprochnogo nikelevogo splava (Selective laser melting of heat-resistant nickel alloy). Tsvetnye Metally = Non-ferrous metals. 2015. No. 1. pp. 79–83.
4. Chlebus E., Kuz’nicka B., Kurzynowski T., Dybaa B. Microstructure and mechanical behaviour of Ti – 6Al – 7Nb alloy produced by selective laser melting. Materials Characterization. 2011. Vol. 62, No. 5. pp. 488–495.
5. Attar H., Calin M., Zhang L. C., Scudino S., Eckert J. Manufacture by selective laser melting and mechanical behavior of commercially pure titanium. Materials Science and Engineering: A. 2014. Vol. 593. pp. 170–177.
6. Gong H., Rafi Kh., Gu H., Starr Th., Stucker B. Analisys of Defect Genereation in Ti–6Al–4V Parts Made using Powder Bed Fusion Additive Manufacturing Processes. Additive manufacturing. 2014. Vol. 1–4. pp. 87–98.
7. Averyanova M., Bertrand Ph., Verquin B. Studying the influence of initial powder characteristics on the properties of final parts manufactured by the selective laser melting technology. Virtual and Physical Prototyping. 2011. Vol. 6, No. 4. pp. 215–223.
8. Vrancken B., Thijs L., Kruth J. P., Van Humbeeck J. Heat treatment of Ti6Al4V produced by selective laser melting: microstructure and mechanical properties. Journal of Alloys and Compounds. 2012. Vol. 541. pp. 177–185.
9. Vilaro T., Colin C., Bartout J. D. As-fabricated and heat-treated microstructures of the Ti–6Al–4V alloy processed by selective laser melting. Metallurgical and Materials Transactions A. 2011. Vol. 42, No. 10. pp. 3190–3199.
10. Facchini L., Magalini E., Robotti P., Molinari A., Höges S., Wissenbach K. Ductility of a Ti–6Al–4V alloy produced by selective laser melting of prealloyed powders. Rapid Prototyping Journal. 2010. Vol. 16, No. 6. pp. 450–459.
11. Simonelli M., Tse Y. The formation of + microstructure in as-fabricated selective laser melting of Ti – 6Al – 4V. Journal of Materials Research. 2014. Vol. 29, No. 17. pp. 2028–2035.
12. GOST 10157–79. Argon gazoobraznyy i zhidkiy. Tekhnicheskie usloviya (State Standard 10157-79. Gaseous and liquid argon. Technical requirements). Introduced: 1980–07–01. (in Russian)
13. GOST 25849–83. Poroshki metallicheskie. Metod opredeleniya formy chastits (State Standard 25849-83. Metallic powders. Method of definition of particle shape). Introduced: 1984–01–01. (in Russian)
14. GOST 1497–84. Metally. Metody ispytaniy na rastyazhenie (State Standard 1497–84. Metals. Pull test methods). Introduced: 1986–01–01. (in Russian)
15. GOST 9651–84. Metally. Metody ispytaniya na rastyazhenie pri povyshennykh temperaturakh (State Standard 9651-84. Metals. Pull test methods with increased temperatures). Introduced: 1986–01–01. (in Russian)
16. GOST 9454–78. Metally. Metody ispytaniya na udarnyy izgib pri ponizhennykh, komnatnoy i povyshennykh temperaturakh (State Standard 9454-78. Impact bending tests with high, room and low temperatures). Introduced: 1979–01–01. (in Russian)
17. ASTM F2924–14. Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion.
18. EOS. EOS Titanium Ti64. Available at: http://ip-saas-eos-cms.s3.amazonaws.com/public/fe8d0271508e1e03/78e37a19596648ee1e1f660a5aa3e622/EOS_Titanium_Ti64_en.pdf.
19. SLM Solutions. SLM materials. Discover the variety. Available at: http://stage.slm-solutions.com/download.php?f=0c4e94b4e06f805e65f3698bf1ff391e.

Language of full-text english
Full content Buy
Back