Journals →  Chernye Metally →  2017 →  #9 →  Back

Tubemaking
ArticleName Features of roll forming in tube billet production
ArticleAuthor V. G. Ilyichev
ArticleAuthorData

All-Russian Scientific and Research Institute of Tube Industry — RosNITI (Chelyabinsk, Russia):

Ilyichev V. G., Cand. Eng., Associate Prof., Head of Laboratory of Large Diameter Tubes, e-mail: zalavin@rosniti.ru

Abstract

The article observes the featured of roll forming of tube billet perimeter geometry and creation of local sections of equidistance violation between cross section shape and circumference of this billet. The technological approaches allowing to prevent forming of anomalous sections, to minimize local defects of shape geometry and, respectively, to provide the most favourable conditions for quality improvement of finished products are suggested. These approaches have been developed on the base of complex analysis of the mechanism of forming operations in the conditions of TRB process for large diameter tubemaking. The results of simulation confirm efficiency of taken solutions. The conducted investigations testify about possibility of control and management on tube billet cross section shape.

keywords Tube billets, deviations, cross section, shape, perimeter, roll forming, bending, equidistance, TRB process
References

1. Vlasov V. Z. General theory of shells and its application in engineering. Moscow : Gostekhizdat, 1949.

2. Bezukhov N. I. Basis of elastic strength, plasticity and creep theory. Moscow : Vysshaya shkola, 1961.
3. Ilyichev V. G., Zalavin Ya. E. Experimental definition of friction forces in deformation zone during the large diameter pipe molding with low D/H ratio in the conditions of JSC «VTZ». Collection of reports of international scientific-technical congress “Metal forming — 2014. Fundamental problems. Innovation materials and technologies. Part 2”. Moscow : LLC «Belyy veter», 2014. pp. 153–159.
4. Shabalov I. P., Samusev S. V., Solovev D. M., Filippov G. A. Definition of extremal cross-sections of pipe billet of various process flowsheets for investigations of consumer performance of main gasline pipes. Problemy chernoy metallurgii i materialovedeniya. 2012. No. 2. pp. 94–100.
5. Shabalov I. P., Solovev D. M., Filippov G. A., Livanova O. V. Influence of 3-roll bending process on the mechanical properties of the metal of large diameter electric-welded pipes. Problemy chernoy metallurgii i materialovedeniya. 2015. No. 1. pp. 60–69.
6. Shinkin V. N., Kolikov A. P. Elastoplastic shaping of metal in an edgebending press in the manufacture of large-diameter pipe. Steel in Translation. 2011. Vol. 41, No. 6. pp. 528–531.
7. Rykalin N. N. Calculation of thermal processes during welding. Moscow : Mashgiz, 1951.
8. Okerblom N. O. Welding deformations and stresses. Moscow : Mashgiz, 1948.
9. Ilyichev V. G., Zalavin Ya. E. Technological peculiarities and reserves of improvement of geometrical characteristics during the Waelz molding for large diameter pipes. Stal. 2016. No. 1. pp. 32–36.
10. Ilyichev V. G., Zalavin Ya. E. Technological reserves of improvement of quality of geometrical characteristics of large diameter pipes during molding in Waelz furnaces. Proceedings of Intenrnational scientific and technical conference “Pipes 2014”. Chelyabinsk, 2015.
11. Shinkin V. N., Kolikov A. P. Simulation of the shaping of blanks for largediameter pipe. Steel in Translation. 2011. Vol. 41, No. 1. pp. 61–66.
12. Shinkin V. N., Kolikov A. P. Engineering calculations for processes involved in the production of large-diameter pipes by the SMS Meer technology. Metallurgist. 2012. Vol. 55, No. 11–12. pp. 833–840.
13. Banakhevych Yu. V., Banakhevych R. Yu., Dragilev A. V., Kychma A. O. Static strength evaluation of pipelines sections with crack-line defects in the weld sone. Hydrocarbon Power Engineering 2014. No. 2. pp. 96–102.

Language of full-text russian
Full content Buy
Back