Журналы →  Chernye Metally →  2018 →  №5 →  Назад

Continuous casting and foundry production
Название Innovative technology of manufacture of shell ceramic forms for fabrication of castings on removable models
Автор I. O. Leushin, L. I. Leushina, O. S. Koshelev
Информация об авторе

Nizhniy Novgorod State Technical University (Nizhniy Novgorod, Russia):

I. O. Leushin, Dr. Eng., Prof., Head of the chair “Metallurgical equipment and technologies”, e-mail: igoleu@yandex.ru
L. I. Leushina, Cand Eng., Associate Prof., e-mail: kafmto@mail.ru
O. S. Koshelev, Dr. Eng., Prof., Chair “Machine-building technological complexes”

Реферат

Drying of the shell after the application of the next layer of slurry and refractory covering material to the model is one of the limiting operations of the technological process for the production of castings for removable (melted, burned, gasified) models. The article presents a critical analysis of some known solutions of the problem of reducing the duration of layer-by-layer drying of the suspension and coating applied to the model block. An alternative providing introduction of a small amount of alum into the composition of applied refractory coating material is proposed. The hydrophilicity of alum along with the acceleration of the drying process in the open air allows to provide in a short period of time gelatination, thereby preventing washing of the applied layer from being washed off during subsequent immersion in the slurry of the refractory filler in the binder solution. At the same time, the coacervation effect is quickly achieved and fixed upon contact of the dusting with the suspension, thereby reducing the necessary drying time and improving the environmental friendliness of the process. The chemical nature of the binder does not change, which preserves its adhesive ability and, as a result, provides high strength properties of the shell material. At the same time, the probability of swelling of the previous layer is minimized when it is wetted by the next layer, leading to buckling and swelling of the shell. As a result, a high level of manufacturability of the ceramic shells is ensured and a minimum of casting defects due to the shape fault is consequently achieved. The sequence of manufacturing operations in the basic technology of manufacture of shell moulds for casting on removable models does not change, additional equipment is not required, additional personnel is not involved. Innovative technology has been successfully tested under current production conditions and recommended for use.

Ключевые слова сastings on removable models, shell ceramic mould, model block, suspension, covering material, drying, coacervation, alum
Библиографический список

1. Ivanov V. N., Kazennov S. A., Kurchman B. S. et al., edited by Shklennik Ya. I., Ozerov V. A. Investment casting. Moscow: Mashinostroenie, 1984. 408 p.
2. Kless P., Vogel M. Feingießen im 21 Jahrhundert. Giesserei. 2008. No. 5. pp. 120–123.
3. Kügelgen M. Schneller Feinguss. Giesserei. 2013. No. 6. pp. 78–82.
4. Janke T. Kooperierende Roboter spreizen Gusstrauben. Giesserei. 2013. No. 7. pp. 60–61.
5. Schütze R., Ansorg M. Grenzwertbeschreibung für das Trocknen von Wasserschlichten. Giesserei. 2012. No. 4. pp. 104–108.
6. Kügelgen M. Auf die Plätze, fertig, trocken! Giesserei. 2007. No. 1. pp. 84–87.
7. Hochgeschwindigkeits-Trocknung von Keramikschalen für den Feinguss. Giesserei. 2007. No. 3. pp. 72.
8. Neue Technik der Schalenherstellung für Feinguss. Giesserei. 2005. No. 2. pp. 108.
9. Redkin I. A. Development and study of the process for drying of shell molds under three-dimensional stress state: thesis of inaguaration of Dissertation … Candidate of Technical Sciences: 05.16.04. Redkin Ivan Alexandrovich. Moscow: 2010. 16 p.
10. Murkina A. S. Binding solutions in the investment casting production. Liteyshchik Rossii. 2013. No. 2. pp. 14–16.
11. Sokolov A. V., Nikitin K. V. Utilization of Al-containing slags recycling products for a ceramic shell at investment casting, based on watercolloidal binders. Liteynoe proizvodstvo. 2016. No. 4. pp. 14–16.
12. Uglev N. P., Poylov V. Z., Zvezdin V. P., Shilov A. V. et al. Properties of ceramic suspensions on the base of aqueous colloidal binders. Liteynoe proizvodstvo. 2016. No. 3. pp. 21–25.
13. Koltygin A. V., Bazhenov V. E., Fadeev A. V. Improvement of casting technology of large aircraft engine parts, made of VT20L (ВТ20Л) alloy, using computer simulation methods. Tsvetnye metally. 2015. No. 5. pp. 80–85.
14. Antipenko V. F. et al. Suspension for fabrication of shell molds for investment casting. Certificate of authorship No. 1507510 USSR, IPC В22 С9/00, 9/12. Patent holder: Kharkovsky filial vsesoyuznogo nauchno-issledovatelskogo institute liteynogo mashinostroeniya, liteynoy tekhnologii i avtomatizatsii liteynogo proizvodstva, published: 15.09.1989.
15. Gyunter G. et al. Method for shell mould drying: certificate of authorship No. 1445848 USSR, ICP В22 С9/04, 9/12. Patent holder: VEB Kombinat Giessereianlagebau und Gusserzeugnisse GISAG, published: 23.12.1988.
16. Bulavin V. I. et al. Manufacturing method of multilayer shell moulds for investment casting (versions). Patent RF, No. 2368452 RF, ICP B22 C1/04. Patent holder: GOU VPO «Yuzhno-Uralsky gosudarstvennyy universitet», published: 27.09.2009. Bulletin No. 27.
17. Pomeranets A. A. et al. Manufacturing method of shell ceramic moulds. Patent RF No. 2025192 RF. ICP В22 С9/04. Patent holder: Kievskoe nauchno-proizvodstvennoe objedinenie po avtomatizatsii I mekhanizatsii tekhnologii proizvodstva. Applied: 21.09.1987. Published: 30.12.1994.
18. KhiMiK: website about chemistry. Available at : http://xumuk.ru/bse/1300.html (accessed 11.01.2018).
19. Leushin I. O. et al. Method of making shell ceramic molds. Patent RF No. 2604281 RF, ICP В22 С1/00, 9/04. Patent holder: FGBOU VO «Nizhegorodsky gosudarstvennyy tekhnicheskyi universitet im. R. Е. Alexeeva», Applied: 03.06.2015. Published: 10.12.2016.
20. Leushin I. O. et al. Dusting material for manufacture of shell-type moulds as per moulten out models, Patent RF No. 2532765 RF, ICP B22C9/04. Patent holder: FGBOU VO «Nizhegorodsky gosudarstvennyy tekhnicheskyi universitet im. R. Е. Alexeeva», Applied: 22.10.2013. Published: 10.11.2014. Bulletin No. 31.

Language of full-text русский
Полный текст статьи Получить
Назад