Journals →  Tsvetnye Metally →  2021 →  #3 →  Back

COMPOSITES AND MULTIPURPOSE COATINGS
ArticleName Deposition of tantalum carbide on Ti6Al4V alloy by electric discharge treatment
DOI 10.17580/tsm.2021.03.08
ArticleAuthor Burkov А. А., Kulik M. A.
ArticleAuthorData

Institute of Materials Science, Khabarovsk Scientific Center, Far Eastern Branch, Russian Academy of Sciences, Khabarovsk:

А. А. Burkov, Senior Researcher, Candidate of Phys.-Math. Sciences, e-mail: burkovalex@mail.ru
M. A. Kulik, Junior Researcher

Abstract

Titanium alloys attract wide attention of researchers due to the unique combination of low density, high strength, corrosion resistance, biocompatibility, etc. Therefore, the study of new methods for processing titanium and the creation of protective coatings seems relevant. Metal-ceramic coatings were obtained by electrospark treatment of a titanium alloy Ti6Al4V in a mixture of titanium granules with tantalum carbide powder. Three mixtures of granules were prepared with a TaC content of 2.4; 4.6 and 6.7 vol.%. Coatings were deposited by rectangular pulses with an energy of 0.33 J and a frequency of 1 kHz for 8 minutes in an argon stream. The increase of the volume fraction of tantalum carbide powder in the mixture of granules from 2.4 to 6.7 vol.% does not lead to a significant increase in cathode gain. The average coating thickness ranged from 29 to 36 microns. Using scanning microscopy and energy dispersive analysis methods, it was found that the coating structure is represented by a metal Ti – Ta – C matrix with large ceramic grains. According to x-ray phase analysis, it was found that tantalum carbide TaC prevails in the coating composition. It content increases with increasing powder concentration in the mixture of granules. In addition to it, there are phases of titanium carbide and tantalum subcarbibide TaC0.6, which are the products of TaC decarburization during its interaction with the titanium melt. With an increase of the tantalum carbide concentration in the mixture of granules, the hardness of TaC/Ti coatings increased from 6.1 to 8.9 GPa, which is 2–3 times higher than that of the Ti6Al4V alloy. Coefficient of friction of coatings was in the range of 0.5–0.9. Dry sliding wear tests showed that TaC/Ti coatings had a wear rate ranging from 0.1·10–5 mm3/Nm to 1.7·10–5 mm3/Nm. Thus, the use of these coatings makes it possible to increase the wear resistance of the Ti6Al4V alloy up to 128 times.

keywords Ti6Al4V alloy, electrospark granule deposition, tantalum carbide, titanium carbide, hardness, wear, friction coefficient, oxidation resistance
References

1. Jakobsen S. S., Lidén C., Søballe K., Johansen J. D. et al. Failure of total hip implants: Metals and metal release in 52 cases. Contact Dermatitis. 2014. Vol. 71. pp. 319–325.
2. Liu Y., Liu W., Ma Y., Liang C. et al. Microstructure and wear resistance of compositionally graded Ti – Al intermetallic coating on Ti6Al4V alloy fabricated by laser powder deposition. Surface and Coatings Technology. 2018. Vol. 353. pp. 32–40.

3. epicka M., Gradzka-Dahlke M. Surface modification of Ti6Al4V titanium alloy for biomedical applications and its effect on tribological performance. A review. Reviews on Advanced Materials Science. 2016. Vol. 46. pp. 86–103.
4. Dai J., Li S., Zhang H., Yu H. et al. Microstructure and high-temperature oxidation resistance of Ti – Al – Nb coatings on a Ti – 6Al – 4V alloy fabricated by laser surface alloying. Surface and Coatings Technology. 2018. Vol. 344. pp. 479–488.
5. Hao Y. J., Liu J. X., Li J. C., Li S. K. et al. Rapid preparation of TiC reinforced Ti6Al4V based composites by carburizing method through spark plasma sintering technique. Materials and Design. 2015. Vol. 65. pp. 94–97.
6. Peretti V., Ferraris S., Gautier G., Hellmich C. et al. Surface treatments for boriding of Ti6Al4V alloy in view of applications as a biomaterial. Tribology International. 2018. Vol. 126. pp. 21–28.
7. Kislyiy P. S., Bodnaruk N. I., Borovikova M. S. Cermets. Kiev : Naukova Dumka, 1985. — 271 p.
8. Tinklepaugh J. R., James R. Cermets. New York : USA, Reinhold Publishing Corporation, 1960. pp. 34–39.
9. Geng G., Liu L., Wang Y., Hai W. et al. Microstructure and mechanical properties of TaC ceramics with 1–7.5 mol.% Si as sintering aid. Journal of the American Ceramic Society. 2017. Vol. 100. pp. 2461–2470.
10. Feng G., Li H., Yao X., Chen M. et al. Ablation resistance of TaC-modified HfC coating prepared by supersonic plasma spraying for SiC-coated carbon/carbon composites. Ceramics International. 2019. Vol. 45, Iss. 14. pp. 17936–17945.
11. Xi W., Ding W., Yu S., Lin N. et al. Corrosion behavior of TaC/Ta composite coatings on C17200 alloy by plasma surface alloying and CVD carburizing. Surface and Coatings Technology. 2019. Vol. 359. pp. 426–432.
12. Dhakal D. R., Gyawali G., Kshetri Y. K., Choi J.-H. et al. Microstructural and electrochemical corrosion properties of electroless Ni – P – TaC com posite coating. Surface and Coatings Technology. 2020. Vol. 381. art. no. 125135.
13. Long Y., Javed A., Chen J., Chen Z.-K. et al. The effect of deposition temperature on the microstructure and mechanical properties of TaC coatings. Materials Letters. 2014. Vol. 121. pp. 202–205.
14. Chao M.-J., Wang W.-L., Liang E.-J., Ouyang D. Microstructure and wear resistance of TaC reinforced Ni-based coating by laser cladding. Surface and Coatings Technology. 2008. Vol. 202, Iss. 10. pp. 1918–1922.
15. Trignan-Piot L., Bérardo M., Gastaldi J., Giorgio S. Influence of plasma spraying parameters on the carbon content and porosity of TaC coatings. Surface and Coatings Technology. 1996. Vol. 79. pp. 113–118.
16. Xie Y., Yang Y., Wang M., Hou J. MCrAlY/TaC metal matrix composite coatings produced by electrospark deposition. Acta Metallurgica Sinica (English Letters). 2013. Vol. 26, Iss. 2. pp. 173–176.
17. Nikolenko S. V., Syuy N. A., Burkov A. A. Investigation of microstructure and properties of coatings on the steel 45, applied by TiC – Ni – Mo based electric discharge deposition. Tsvetnye Metally. 2017. No. 4. pp. 69–75.
18. Burkov А. А., Kulik М. А., Krutikova V. O. Characteristics of Ti–Si coatings on Ti6Al4V Alloy Subjected to Electrospark Granules Deposition. Tsvetnye Metally. 2019. No. 4. pp. 54–59. DOI: 10.17580/tsm.2019.04.07.
19. Burkov A. A., Chigrin P. G. Effect of tungsten, molybdenum, nickel and cobalt on the corrosion and wear performance of Fe-based metallic glass coatings. Surface and Coatings Technology. 2018. Vol. 351. pp. 68–77.
20. Poveshchenko V. I., Egorov F. F., Verkhoturov A. D. Electric-spark alloying of steels with TiN-Cr materials. Powder Metall Met Ceram. 1983. Vol. 22. pp. 910–915.
21. ASTM G99 – 04a. Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus. PA, West Conshohocken, 2004.
22. Chen G. X., Zhou Z. R., Kapsa Ph., Vincent L. Effect of surface topography on formation of squeal under reciprocating sliding. Wear. 2002. Vol. 253. pp. 411–423.
23. Liu Y., Zheng Z., Yang C., Zhu D. et al. Effects of unreacted Ti particles on the dry sliding tribological behavior of squeeze-cast (SiCp + Ti)/7075Al hybrid composites under different applied loads. Tribology Letters. 2017. Vol. 65. p. 39.
24. Stott F. H., Jordan M. P. The effects of load and substrate hardness on the development and maintenance of wear-protective layers during sliding at elevated temperatures. Wear. 2001. Vol. 250–251. pp. 391–400.
25. Wei M. X., Wang S. Q., Wang L., Cui X. H. Wear and friction characteristics of a selected stainless steel. Tribology Transactions. 2011. Vol. 54. pp. 840–848.
26. Li G. D., Xiong X., Huang K. L. Ablation mechanism of TaC coating fabricated by chemical vapor deposition on carbon-carbon composites. Trans. Nonferrous Met. Soc. China. 2009. Vol. 19. pp. S689–S693.
27. Lv Y. H., Li J., Tao Y. F., Hu L. F. High-temperature wear and oxidation behaviors of TiNi/Ti2Ni matrix composite coatings with TaC addition prepared on Ti6Al4V by laser cladding. Applied Surface Science. 2017. Vol. 402. pp. 478–494.

Language of full-text russian
Full content Buy
Back