Журналы →  Non-ferrous Мetals →  2021 →  №1 →  Назад

METAL PROCESSING
Название Application of plasma surfacing for additive formation of titanium alloy billets
DOI 10.17580/nfm.2021.01.08
Автор Shchitsyn Yu. D., Krivonosova Е. А., Olshanskaya Т. V., Neulybin S. D.
Информация об авторе

Perm National Research Polytechnic University, Perm, Russia:

Yu. D. Shchitsyn, Professor, Head of the Department of Welding, Metrology and Materials Engineering (DWMME), e-mail: schicin@pstu.ru
Е. А. Krivonosova, Professor, DWMME, e-mail: katerinakkkkk@mail.ru
Т. V. Olshanskaya, Associate Professor, DWMME, e-mail: tvo66@mail.ru
S. D. Neulybin, Engineer, DWMME, e-mail: sn-1991@mail.ru

Реферат

This paper presents the findings of an investigation on the main formation regularities of structure and properties of VT20 (ВТ20) superalloy of Ti – Al – V – Mo – Zr system in hybrid technology of additive manufacturing with the use of plasma surfacing with layer-by-layer strain hardening. When studying the effect of forging on the structure and properties of surfacing material, three processing schemes were implemented: surfacing with forging of a next to last layer; surfacing with forging of the last layer; surfacing with forging of each layer. Investigated is the morphology of the built-up layers’ structure, which is associated with various cooling rates at the stages of crystallization and transformations in the solid state: at high cooling rate, a basket weave structure is forming, and a martensite-like lamellar structure arises on slow cooling. Different dispersities of the plates of α-colonies were fixed — from 200 to 500 μm, the size of individual needles varies from fractions of a micron to 100 μm. It is established that the layer-by-layer deformation impact, which contributes to the titanium alloy structure grinding and a rise in dispersion of the α-phase plates, is accompanied by an increase in microhardness to the level of 6000 HV. The formation of a finer structure during surfacing with a layer-by-layer deformation effect is obviously bound up with the martensate phase lightened growth on a pre-crushed metal substrate with an increased dislocation density. It is established that the strength properties of the obtained VT20 alloy surfacings exceed the strength level of materials made by traditional forming technologies, and there is no decrease in the plasticity characteristics.

The work was carried out with the financial support of the Ministry of Education and Science of the Russian Federation according to the State task No. FSNM-2020-0028, the Ministry of Education and Science of the Perm Region in accordance with the Agreement S-26/511 of 09.03.2021 and the RFBR grant 20-48-596006 r_SEC_Perm Region.

Ключевые слова Titanium alloys, additive technologies, plasma surfacing, layer-by-layer deformation impact, structure, properties
Библиографический список

1. Shchitsyn Yu. D., Krivonosova Е. А., Olshanskaya Т. V., Neulybin S. D. Structure and Properties of Aluminium – Magnesium – Scandium Alloy Resultant from the Application of Plasma Welding with by-Layer Deformation Hardening. Tsvetnye Metally. 2020. No. 2. pp. 89–94. DOI: 10.17580/tsm.2020.02.12.
2. Wu B., Pan Z., Ding D., Cuiuri D., Li H., Xu J., Norrish J. A Review of the Wire Arc Additive Manufacturing of Metals: Properties, Defects and Quality Improvement. Journal of Manufacturing Processes. 2018. Vol. 35. pp. 127–139.
3. Tabernero I., Paskual A., lvarez P., Su rez A. Study on Arc Welding Processes for High Deposition Rate Additive Manufacturing. Procedia CIRP. 2018. Vol. 68. pp. 358–362.
4. Lockett Н., Ding J., Williams S., Martina F. Design for Wire + Arc Additive Manufacture: Design Rules and Build Orientation Selection. Journal of Engineering Design. 2017. Vol. 28, Iss. 7-9. pp. 568–598.
5. Oskolkov A. A., Matveev E. V., Bezukladnikov I. I., Trushnikov D. N., Krotova E. L. Advanced Technologies for Additive Manufacturing of Metal Product. Bulletin PNRPU. Mechanical Engineering, Materials Science. 2018. Vol. 20, No. 3. pp. 90–105.
6. Krivonosova E. A., Schitsin Yu. D., Trushnikov D. N., Myshkina S. N., Akulova A. V., Neulybin S. D., Dushina A. Yu. Influence of Surfacing Technologies on Structure Formation of High-Temperature Nickel Alloys. Metallurgist. 2019. Vol. 63, Iss. 1-2. pp. 197–205.
7. Shchitsin Yu. D., Krivonosova E. A., Neulubin S. D., Olshanskaya T. V., Nikulin R. G., Fedoseeva E. M., Terentyev S. A. Use of Plasma Surface for Additive Formation of Aluminum Alloys Blade. Bulletin PNRPU. Mechanical Engineering, Materials Science. 2019. Vol. 21, No. 2. pp. 63–72.
8. Isaenkova M. G., Perlovich Yu. A., Babich Ya. A., Medvedev P. N. Evolution of Structure, Crystallographic Texture and Mechanical Properties in Innovative Titanium Alloys During Plastic Deformation and Heat Treatment. Tsvetnye Metally. 2020. No. 4. pp. 58–70. DOI: 10.17580/tsm.2020.04.07.
9. Donoghue J., Antonysamy A. A., Martina F., Colegrove P. A., Williams S. W., Prangnell P. B. The Effectiveness of Combining Rolling Deformation with Wire–Arc Additive Manufacture on β-Grain Refinement and Texture Modification in Ti – 6Al – 4V. Materials Characterization. 2016. Vol. 114. pp. 103–114.
10. Wu Q., Lu J., Liu C., Fan H., Shi X., Fu J., Ma S. Effect of Molten Pool Size on Microstructure and Tensile Properties of Wire Arc Additive Manufacturing of Ti – 6Al – 4V Alloy. Materials. 2017. Vol. 10, Iss. 7. p. 749.
11. McAndrew A. R., Rosales M. A., Colegrove P. A., Hönnige J. R., Ho A., Fayolle R., Eyitayo K., Stan I., Sukrongpang P., Crochemore A., Pinter Z. Interpass Rolling of Ti – 6Al – 4V Wire + Arc Additively Manufactured Features for Microstructural Refinement. Additive Manufacturing. 2018. Vol. 21. pp. 340–349.
12. Hirtler M., Jedynak A., Sydow B., Sviridov A., Bambach M. Investigation of Microstructure and Hardness of a Rib Geometry Produced by Metal Forming and Wire-Arc Additive Manufacturing. MATEC Web of Conferences. 2018. Vol. 190. 02005. DOI: 10.1051/matecconf/201819002005
13. Martina F., Williams S. W., Colegrove P. A. Improved Microstructure and Increased Mechanical Properties of Additive Manufacture produced Ti–6Al–4V by Interpass Cold Rolling. 24th International Solid Freeform Fabrication Symposium, Austin, Texas, USA, 2013. pp. 490–496.
14. Kapil S., Legesse F., Kulkarni P. M., Joshi P., Desai A., Karunakaran К. P. Hybrid-Layered Manufacturing Using Tungsten Inert Gas Cladding. Progressing Additive Manufacturing. 2016. Vol. 1. Iss. 1-2. pp. 79–91.
15. Lukin V. I., Ioda E. N., Panteleev M. D., Skypov A. A. Fusion Welding of VT18U Titanium Alloy. Proceedings of VIAM. 2015. No. 5. pp. 1–13.
16. Borisova E. A., Bochvar G. A., Brun M. Ya. et al. Titanium alloys. Metallography of Titanium Alloys. Moscow: Metallurigiya, 1980. 464 p.
17. Neulybin S. D., Permyakov G. L., Trushnikov D. N., Shchitsyn Y. D., Belenkiy V. Y. Development of a Dynamic Model of Thermal Processes for Plasma Surfacing at Direct and Reverse Polarity. International Journal of Applied Engineering Research. 2017. Vol. 12, No. 22. pp. 11847–11854.
18. Kashapov O. S., Pavlova T. V., Kondrateva A. R., Kalashnikov V. S. Peculiarities of Application of Heat-Resistant Titanium Alloy VT8-1 (ВТ8-1) for the Bladed Integrated Disks of Gas-Turbine Engine Compressor. Tsvetnye Metally. 2016. No. 5. pp. 63–69. DOI: 10.17580/tsm.2016.05.10.
19. Sufiyarov V. Sh., Popovich A. A., Borisov E. V., Polozov I. A. Selective Laser Melting of Titanium Alloy and Manufacturing of Gas-Turbine Engine Part Blanks. Tsvetnye Metally. 2015. No. 8. pp. 76–80. DOI: 10.17580/tsm.2015.08.11.

Полный текст статьи Application of plasma surfacing for additive formation of titanium alloy billets
Назад