Journals →  Chernye Metally →  2021 →  #6 →  Back

Rolling and Heat Treatment
ArticleName Mathematical model for calculating the parameters of straightening section profiles on a roller straightening machine
DOI 10.17580/chm.2021.06.03
ArticleAuthor E. A. Maksimov, R. L. Shatalov
ArticleAuthorData

JSC Intray,(Chelyabinsk, Russia):
E. A. Maksimov, Cand. Eng., Technologist, e-mail: maksimov50@mail.ru

 

Moscow Polytechnic University (Moscow, Russia):

R. L. Shatalov, Dr. Eng., Prof., e-mail: mmomd@mail.ru

Abstract

The analysis of the traditional theories of straightening section and shaped steel on a roller straightening machine (RSM) according to the methods of Korolev and Tselikov - Smirnov, using the linear law of change in the coefficient of penetration of plastic deformation along the height of the rolled product. It is shown that when straightening a steel angle 200 - 200 - 24 mm (σs = 440 MPa) on a nine-roller straightening machine (SM), the greatest discrepancy in the calculation of bending moments and straightening forces according to the Korolev and Tselikov - Smirnov methods is equal to 25 % and is observed on roller No. 4. A refined mathematical model is proposed to calculate the parameters of straightening of long products on the RSM. It provides a more accurate definition of the boundary between the elastic and plastic zones as a result of taking into account the bending hardening. On the basis of the developed model, an algorithm to calculate the straightening parameters of long products for an eight-roller SM of the universal rolling mill 650 of the Nizhniy Tagil Metallurgical Plant (NTMK) has been compiled. Comparative results of the calculated and experimental straightening forces for hardened rails 65R on the eight-roller SM of the plant are presented, confirming the adequacy of the developed model with an error of 20 %. The results of the study can be applied in calculating the parameters of straightening profiled sections, as well as in the modernization and design of RSM.

keywords Straightening of long products, roller straightening machine, non-straightness defect, mathematical model
References

1. GOST 21014–88. Rolled products of ferrous metals. Surface defects. Terms and definitions. Introduced: 01.01.1990.
2. Korolev А. А. Design and calculation of machines and mechanisms of rolling mills. Moscow: Metallurgiya, 1985. 376 p.
3. Tselikov А. I., Smirnov V. B. Rolling mills. Moscow: Metallurgizdat, 1958. 432 p.
4. Slonim А. Z., Sonin А. L. Straightening of sheet and long products. Moscow: Metallurgiya, 1981. 232 p.
5. GOST 21014–88. П Rolled products of ferrous metals. Surface defects. Terms and definitions. Introduced: 01.01.1990.
6. Shinkin V. N. Failure of large-diameter steel pipe with rolling scabs. Steel in Translation. 2017. Vol. 47. No. 6. P. 363–368.
7. Kaden V. High performance leveler for hot and cold leveling of heavy plates. Met. Plant and Tech. 2007. No. 2. pp. 92–94.
8. Nedorezov I. V. Simulation of processes of straightening the rolled products on roller machines. Ekaterinburg: AKVA-press, 2003. 256 p.
9. Nedorezov I. V., Orlov B. Ya., Titarenko V. I. Roller straightening machines for thick plates. Stal. 1999. No. 9. pp. 40–42.
10. Nedorezov I. V., Volegov B. Ya., Orlov B. Ya. Reduction of residual stresses in unhardened rails when straightening without a torque method. Stal. 1999. No. 9. pp. 66–68.
11. Nedorezov I. V., Polyakov A. P., Volegov B. Ya. Methods to determinate residual stresses in unhardened rails. Proizvodstvo prokata. 2001. No. 2. pp. 11–16.
12. Nedorezov I. V. Overview of industrial processes of hardening rails and residual stresses in them. Proizvodstvo prokata. 2001. No. 6. pp. 13–18.
13. Shinkin V. N. The mathematical model of the thick steel sheet flattening on the twelve-roller sheet-straightening machine. Message 1. Curvature of sheet. CIS Iron and Steel Review. 2016. Vol. 12. pp. 37–40. DOI: 10.17580/cisisr.2016.02.08.
14. Shinkin V.N. Simplified calculation of the bending torques of steel sheet and the roller reaction in a straightening machine. Steel in Translation. 2017. Vol. 47. No. 10. pp. 639-644.
15. Maksimov Е. А., Shatalov R. L. Improvement of the quality of building steel sheets by straightening them on a roller straightening machine. Chernaya metallurgiya. Byulleten nauchnotekhnicheskoy i ekonomicheskoy informatsii. 2018. No. 6. pp. 49–55.
16. Sharma H. V. Resent measures to improve quality of rails. Technical Journal of Bhilai Steel. 2008. No. 5. pp. 21–23.
17. Bramfitl B. Advanced in-line head hardening of rails. Proceeding of the International Symposium. Baltimor, 2015. No. 6. pp. 23–29.
18. Ghevet M. Planeuse a ruoleaux imbriques et procede de mise en oeuvre telle planeuse. Patent 9604683. 2009. pp. 1–5.
19. Irastorsa I. Modelisation of flatness evolution during coaling and leveling of plate as a for production desing. Metec Congress. Dusseldorf, 2014. pp. 106–111.
20. Garber E. A., Bolobanova N. L., Trusov K. A. Application of the finite element method to reveal the causes of loss of planeness of hot-rolled steel sheets during laser cutting. Russian Metallurgy (Metally). Vol. 2018. No. 1. pp. 90–94.
21. Trusov K. A., Mishnev P. A., Garber E. A., Bolobanova N. L., Nushtaev D. V., Ardatov K. V. Investigation of blank bow defect after roller leveller by finite element analysis. Journal of Physics: Conference Series. 2018. Vol. 1063. 012192. pp. 1–6.
22. Utrata D. Evaluation of web cracking tendencies in rail via various methods. Proceedings of the International Symposium on Rail Steels for the 21st Century. Baltimor. 1994. pp. 131–135.
23. Marten H. Antreibsleistungbeim richten voncrobblechen. Bänder, Bleche, Rohre. 2013. No. 10. pp. 23–26.
24. GOST 8509–93. Hot-rolled steel equal-leg angles. Dimensions. Introduced: 01.01.1997.
25. GOST 51685–2013. Railway rails. General specifications. Introduced: 01.07.2014.

Language of full-text russian
Full content Buy
Back