Journals →  CIS Iron and Steel Review →  2021 →  #1 →  Back

Rolling
ArticleName Mathematical models of temperature in electric discharge rolling of metals
DOI 10.17580/cisisr.2021.01.07
ArticleAuthor A. Yu. Albagachiev, A. M. Keropyan, A. A. Gerasimova, A. N. Pashkov
ArticleAuthorData

Mechanical Engineering Research Institute of the Russian Academy of Sciences – IMASH RAN (Moscow, Russia):

A. Yu. Albagachiev, Dr. Eng., Prof., Head of the “Friction, Wear, Lubrication. Tribology” Dept., e-mail: albagachiev@yandex.ru

 

National University of Science and Technology “MISiS” (Moscow, Russia):
A. M. Keropyan, Dr. Eng., Prof., Dept. of Engineering of Technological Equipment, e-mail: am_kerop@mail.ru
A. A. Gerasimova, Cand. Eng., Associate Prof., Dept. of Engineering of Technological Equipment, e-mail: gerasimova.aa@misis.ru
A. N. Pashkov, Cand. Eng., Associate Prof., Dept. of Engineering of Technological Equipment

Abstract

The model of analytical calculation of the average volumetric temperature of plastic deformation in the conditions of applied impulse current was developed on the base of rolling energy balance. Additionally, the formula for determination of the contact temperature between rolls and strip as well as temperature gradient through strip thickness and its variation in time of electroplastic process conduction was concluded on the base of solution of the heat conductivity differential equation in Fourier partial derivatives. This equation is valid for the boundary condition taking into account joint heating with impulse current and plastic deformation. Conducted temperature calculations for dimensionless time in the deformation area during electric discharge rolling of steel 3 and VT-6 titanium alloy displayed that temperature rise up to its maximal value has temporal displacement to strip exit side of deformation area. It is connected with temporal retarding of heat forming comparing with the time of elastic-plastic deformation. As soon as the contact square of rolls with strip has two different areas, where bonding and slipping are realized via rolling friction and slipping friction, immediate temperatures will also differ respectively. The obtained models allow to conduct calculations of the contact temperatures in the areas of roll bonding and slipping relating to the rolling strip. Electric discharge rolling reduces conventional cold rolling technology via elimination of heating with intermediate heat treatment (annealing) and improves thereby thin strip quality via healing of its cracks and defects by electric impulses, as well as increases productivity by 30 %.

keywords Rolling, electric current, mathematical model, temperature, steel 3, VT-6 titanium alloy, slipping, bonding
References

1. Thiesen P. A Physikalisch-chemische Untersuchungen tribomechnischer Vorgange. Zeitschrift Chemie. 1965, S. 162–171.
2. Troitskiy O. A., Baranov Yu. V., Avraamov Yu. S., Shlyapin A. D. Physical grounds and processing technologies for modern materials. 2 volumes. Vol. 1. Moscow — Izhevsk: Institut kompyuternykh issledovaniy. 2004. 590 p.
3. Fomin A. A., Gusev V. G., Timerbaev N. F. The processing of the profile surface of the work-pieces, characterized by low rigidity. Solid State Phenomena. 2020. 299 SSP. pp. 852–860.
4. Keropyan A., Gerasimova A., Goloshapov K. Influence of the track gradient on the contact temperature at the wheel-rail zone for open-pit locomotives. International Conference on Modern Trends in Manufacturing Technologies and Equipment (ICMTMTE 2017). MATEC Web of Conferences. 2017. 129, 06009.
5. Basyrov I. I., Bardovsky A. D. Innovative crushing technique and vertical roll crusher design. Gornyi informatsionno-analiticheskiy byulleten. 2020. No. 2. pp. 121–129.
6. Kolikov A. P., Romantsev B. A. Theory of metal forming. A manual. Moscow.: Izdatelskiy dom MISiS. 2015. 451 p.
7. Chitkara N. R., Aleem A. Axi-symmetric tube extrusion/piercing using die-mandrel combinations: some experiments and a generalised upper bound analysis. International Journal of Mechanical Sciences. 2001. No. 43. Iss. 7. pp. 1685–1709.
8. Tyurin V. A., Mokhov A. I. Theory of metal forming. A manual for high schools. Volgograd. VolgGTU. 2000. 416 p.
9. Artiukh V., Mazur V., Prakash R. Increasing hot rolling mass of steel sheet products. Solid State Phenomena. 2016. 871, pp. 3–8. DOI: 10.4028/www.scientific.net/MSF.871.
10. Albagachiev A. Yu., Keropyan A. M., Gerasimova A. A., Kobelev O. A. Determination of rational friction temperature in lengthwise rolling. CIS Iron and Steel Review. 2020. Vol. 19. pp. 33–36.
11. Keropyan A. M., Gerasimova А. А. Connection between the temperature in the contact area of the system “wheel — rail” with railway inclination for industrial railroad transport. Izvestiya vuzov. Chernaya metallurgiya. 2017. Vol. 60. No. 5. pp. 355–363. DOI: 10.17073/0368-0797-2017-5-355-363.
12. Chen H., Li F., Li J. Experimental study on pure titanium during the positive-torsion and positive-negative-torsion. Materials Science and Engineering: A. 2016. Vol. 674. pp. 552–568.
13. Fomin A. A., Gusev V. G. Safe machining of blanks with nonuniform properties. Russian Engineering Research. 2013. Vol. 33. No. 10. pp. 602–606. DOI: 10.3103/S1068798X13100043
14. Gerasimova A., Mishedchenko O., Devyatiarova V. Determination of temperature conditions for steel plate rolling at Vyksa Steel Works (AO VMZ). IOP Conf. Series: Materials Science and Engineering. 2020. 709. Iss. 1. 022016. DOI: 10.1088/1757-899X/709/2/022016.
15. Kondratenko V. E., Devyatiarova V. V., Albul S. V., Valeeva L. M. Method of calculating volumetric scaffold of monolithic slab formwork. IOP Conf. Series: Materials Science and Engineering. 2020. 971. No. 052036. P. 32-35. DOI: 10.1088/1757-899X/971/5/052036.
16. Biasoli De Mello J. D., Binder C., Hammes G., Binder R., Klein A. N. Tribological behaviour of sintered iron based selflubricating composites. Friction. 2017. No. 5 (3). pp. 285–307.
17. Holmberg К., Kivikyto-Reponen P., Harkisaari P., Valtonen K., Erdemir A. Global energy consumption due to friction wear in the mining industry. Tribology International. 2017. No. 115. pp. 116–139.
18. Gorbatyuk S. M., Gerasimova A. A., Radyuk A. G. Using the Coating for the Diffusion Layer Obtaining on the Walls of the Mold (CCM). Metallurgical and mining industry. 2015. Iss. 9. рр. 1085–1088.
19. Artiukh, V., Mazur, V., Adamtsevich, A. Priority influence of horizontal forces at rolling on operation of main sheet rolling equipment. MATEC Web of Conferences. 2017. 106. Paper No. 04001. DOI: 10.1051/matecconf/201710604001.

Full content Mathematical models of temperature in electric discharge rolling of metals
Back