Журналы →  Tsvetnye Metally →  2021 →  №11 →  Назад

Название Microstructure and Mechanical Properties of Materials Formed by Diffusion Bonding of VT6 Alloy Parts Produced by Rolling and Selective Laser Melting
DOI 10.17580/tsm.2021.11.10
Автор Travyanov A. Ya., Lagutin A. O., Khomutov M. G., Lukianov V. V.
Информация об авторе

National University of Science and Technology MISiS, Moscow, Russia:

A. Ya. Travyanov, Director of the Institute of Ecotechnology and Engineering, Candidate of Technical Sciences

A. O. Lagutin, Engineer
M. G. Khomutov, Senior Researcher, Candidate of Technical Sciences, e-mail: khomutov@misis.ru


Aviation Technology Park, Research & Production Association, Ufa, Russia:
V. V. Lukianov, Head of the Department, Candidate of Technical Sciences


Nowadays, the rapid development of the new methods of assembling large-scale parts consisting of several materials elaborated by different manufacturing methods is observed. These materials are unique in terms of the mechanical and physical properties of the part. Diffusion welding is one of the most promising multipurpose assembling techniques allowing the formation of lowporous high-quality welding joints with stable mechanical properties and absence of oxide inclusions. This method is widely applied for assembling titanium alloy parts requiring the welding in a vacuum due to the high chemical activity of titanium in the normal atmosphere containing oxygen, nitrogen and hydrogen. In this work, the structure and properties of parts produced from Ti6Al4V titanium alloy by the combination of laser powder bed fusion, hot rolling and diffusion welding were studied. The diffusion welding was performed in an autoclave (at temperature T = 920 оC, pressure 4 MPa, holding time of 4 h) and hot isostatic pressing (at temperature T = 930 оC, pressure 100 MPa, holding time of 2 h). It was shown that the microstructure of the weld joint depended on the welding method (autoclave or HIP). No defects in the zone of diffusion joints were observed in both cases. The impact toughness of samples obtained during hot isostatic pressing is higher than for the samples obtained in an autoclave. Both types of welded samples had high mechanical properties and met the requirements of GOST 23755–79 standard for bulk titanium samples.
The authors would like to thank V. V. Cheverikin, Candidate of Technical Sciences, MISiS, and P. V. Petrovskiy, Candidate of Technical Sciences, MISiS, for conducting metallography studies and discussing the results. This research was funded by the Ministry of Science and Higher Education of the Russian Federation. Within the framenork of the Government Resolution No. 218 based on the Agreement on subvention assignment No. 075-11-2019-058 dated 25.11.2019 “Establishing a production line for locally reinforced titanium alloy components designed to operate under high loads and temperatures as a part of innovative gas turbine engines“.

Ключевые слова Alloy Ti6Al4V, selective laser melting, diffusion welding, hot isostatic pressing, mechanical properties
Библиографический список

1. Eskandari Sabzi H. Powder bed fusion additive layer manufacturing of titanium alloys. Materials Science and Technology. 2019. Vol. 35, No. 8. pp. 875–890.
2. Ju J., Zhao C., Kang V. et al. Effect of heat treatment on microstructure and tribological behavior of Ti – 6Al – 4V alloys fabricated by selective laser melting. Tribology International. 2021. Vol. 159. p. 106966.
3. Oyesola M., Mpofu K., Mathe N. et al. Optimization of selective laser melting process parameters for surface quality performance of the fabricated Ti6Al4V. International Journal of Advanced Manufacturing Technology. 2021. Vol. 114, No. 5-6. pp. 1585–1599.
4. Popovich A. A., Sufiyarov V. Sh., Borisov E. V. et al. Anisotropy of the mechanical properties of parts fabricated by selective laser melting of powder materials. Izvestiya vuzov. Poroshkovaya metallurgiya i funktsionalnye pokrytiya. 2016. No. 3. pp. 4–11.
5. Doubenskaia M., Domashenkov A., Smurov I. et al. Study of selective laser melting of intermetallic TiAl powder using integral analysis. International Journal of Machine Tools and Manufacture. 2018. Vol. 129. pp. 1–14.
6. Manca D. R., Churyumov A. Y., Pozdniakov A. V. et al. Novel heat-resistant Al – Si – Ni – Fe alloy manufactured by selective laser melting. Materials Letters. 2019. Vol. 236. pp. 676–679.

7. Churyumov A. Yu., Pozdniakov A. V., Prosviryakov A. S. et al. Microstructure and mechanical properties of a novel selective laser melted Al – Mg alloy with low Sc content. Materials Research Express. 2019. Vol. 6, No. 12. p. 8.
8. P. V. Petrovsky, V. V. Cheverikin, P. Yu. Sokolov et al. Dependence of the structure and properties of 03Kh16N15M3 steel on the geometry of cellular structures obtained by the selective laser melting method. Chernye Metally. 2019. No. 3. pp. 49–53.
9. Pozdniakov A. V., Churyumov A. Yu., Loginova I. S. et al. Microstructure and properties of novel AlSi11CuMn alloy manufactured by selective laser melting. Materials Letters. 2018. Vol. 225. pp. 33–36.
10. Manca D. R., Churyumov A. Yu., Pozdniakov A. V. et al. Microstructure and properties of novel heat resistant Al – Ce – Cu alloy for additive manufacturing. Metals and Materials International. The Korean Institute of Metals and Materials. 2019. Vol. 25, No. 3. pp. 633–640.
11. Liu S., Shin Y. C. Additive manufacturing of Ti6Al4V alloy: a review. Materials and Design. 2019. Vol. 164. p. 107552.
12. Badiru A. B., Valencia V. V., Liu D. Additive manufacturing handbook: product development for the defense industry. USA : CRC Press. 948 p.
13. Safiullin R. V., Mukhametrakhimov M. Kh., Safiullin A. R. et al. The study of technological properties of the titanium alloy Ti – 6A l – 4V. Part 2. Letters on Materials. 2018. Vol. 8, No. 3. pp. 329–334.
14. Lee H. S., Yoon J. H., Yi Y. M. Solid state diffusion bonding of titanium alloys. Solid State Phenomena. 2007. Vol. 124–126. pp. 1429–1432.
15. Chandrappa K., Sumukha C. S., Sankarsh B. B. et al. Superplastic forming with diffusion bonding of titanium alloys. Materials Today: Proceedings. 2019. Vol. 27. pp. 2909–2913.
16. Yakushina E., Reshetov A., Semenova I. et al. The influence of the microstructure morphology of two phase Ti – 6Al – 4V alloy on the mechanical properties of diffusion bonded joints. Materials Science and Engineering : A. 2018. Vol. 726. pp. 251–258.
17. Jackson M. Superplastic forming and diffusion bonding of titanium alloys. Superplastic Forming of Advanced Metallic Materials. 2011. pp. 227–246.
18. Froes F. H., Mashl S. J., Hebeisen J. C. et al. The technologies of titanium powder metallurgy. Journal of the Minerals Metals and Materials Society. 2004. Vol. 56, No. 11. pp. 46–48.
19. Petrovskiy P., Travyanov A., Cheverikin V. V. et al. Effect of encapsulated hot isostatic pressing on properties of Ti6Al4V deposits produced by cold spray. International Journal of Advanced Manufacturing Technology. 2020. Vol. 107. pp. 437–449.
20. Dowling L., Kennedy J., O‘Shaughnessy S. et al. A review of critical repeatability and reproducibility issues in powder bed fusion. Materials and Design. 2020. Vol. 186. p. 108346.
21. ASTM F3001-14. Standard specification for additive manufacturing titanium-6 aluminum-4 vanadium ELI (Extra Low Interstitial) with Powder Bed Fusion. ASTM Interational. 2014. pp. 1–6.
22. GOST 19807–91. Wrought titanium and titanium alloys. Grades. Introduced: 01.07.1992. Moscow : Izdatelstvo standartov, 1991.
23. GOST 23755–79. Plates of titanium and titanium alloys. Specifications. Introduced: 18.07.1979. Moscow : Izdatelstvo standartov, 1994.
24. GOST 1497–84. Metals. Methods of tension test. Introduced: 01.01.1986. Moscow : Izdatelstvo standartov, 1984.
25. GOST 9454–78. Metals. Method for testing the impact strength at low, room and high temperature. Introduced: 01.01.1979. Moscow : Izdatelstvo standartov, 1978.
26. GOST 14019–2003. Metallic materials. Bend test method. Introduced: 01.09.2004. Moscow : Izdatelstvo standartov, 2003.

Language of full-text русский
Полный текст статьи Получить