Журналы →  CIS Iron and Steel Review →  2021 →  №2 →  Назад

Metal Science and Metallography
Название Study of structure of high-strength cold-resistant steel after quenching and tempering
DOI 10.17580/cisisr.2021.02.11
Автор P. P. Polteskov, I. L. Yakovleva, A. S. Kuznetsova, N. V. Koptseva, O. A. Nikitenko
Информация об авторе

Nosov Magnitogorsk State Technical University, Magnitogorsk, Russia:

P. P. Polteskov, Dr. Eng., Prof., Dept. of Metal Processing Technology
A. S. Kuznetsova, Dept. of Metal Processing Technology, e-mail: allakuznetsova.mgtu@mail.ru
N. V. Koptseva, Dr. Eng., Prof., Dept. of Casting Processes and Materials Science
O. A. Nikitenko, Cand Eng., Associate Prof., Dept. of Metal Processing Technology, e-mail: o.nikitenko@magtu.ru

M. N. Mikheev Institute of Metal Physics of Ural Branch of RAS, Ekaterinburg, Russia:

I. L. Yakovleva, Dr. Eng., Chief Researcher, Laboratory of Physical Metal Science

Реферат

The conditions of heat treatment, providing achievement of high strength characteristics (σ0,2 ≥ 600 N/mm2) in combination with low-temperature impact strength (KCV−60 ≥ 50 J/cm2) and plasticity (δ5 ≥ 17 %), were determined for the new weldable sparingly alloyed steel 20G2SMRA. Steel structure was formed after hot rolling, quenching from the temperature 860 °С and consequent high tempering at the temperature 600 °С (which determined the obtained complex of steel properties) and then was examined via the method of scanning electronic microscopy. The results of energy-dispersion analysis of carbide particles which were extracted during tempering of quenched steel are presented. It is shown that the required level of strength and cold resistance is provided due to forming of mainly finedispersed lath martensite (with α-phase lath width 0.2–0.7 μm) and with small part of residual austenite (about 1 %), as well as dislocation high-temperature martensite. Sub-grain α-phase structure (with size of single sub-grains 0.1–0.7 μm) and cementite-type of carbide particles are formed during tempering.

The research was carried out under financial support of the RF Ministry of Education and Science within execution of the RF President’s grant (Agreement No. 075-15-2020-205/1 dated 29.03.2021 (int. No. MK-1979.2020.8/1)).
Electron microscope examination of foils for clearance were conducted within the boundaries of the State assignment for the theme “Structure”, State reg. No. АААА-А18-118020190116-6.

Ключевые слова Weldable high-strength steel, scanning electronic microscopy, mechanical properties, quenching, tempering
Библиографический список

1. Khlusova E. I., Sych O. V. Creation of cold-resistant structural materials for Arctic region. History, experience, current state. Innovatsii. 2018. No. 11 (241). pp. 85–92.
2. Golubeva M. V., Sych O. V., Khlusova E. I., Motovilina G. D. Study of mechanical properties and destruction features for the new sparingly alloyed cold-resistance steel with guaranteed yield strength 690 MPa. Avaitsionnye materialy i tekhnologii. 2017. No. 4 (49). pp. 19–24.
3. Golubeva M. V., Sych O. V., Khlusova E. I. Development of coldresistant weldable steel with strength class 690 MPa for high-duty machines operating in the Arctic conditions. Tyazheloe mashinostroenie. 2018. No. 4. pp. 17–25.
4. Golosienko S. A. New high-strength cold-resistance steels for Arctic application. Proizvodstvo prokata. 2014. No. 2. pp. 17–24.
5. Poletskov P. P., Nikitenko O. A., Kuznetsova A. S., Salganik V. M. The study of transformation kinetics for overcooled austenite of the new high-strength steel with increased cold resistance. CIS Iron and Steel Review. 2020. Vol. 19. pp. 56–59.
6. Poletskov P. P., Kuznetsova A. S., Nikitenko O. A., Alekseev, D. Yu. The study of influence of heat treatment procedures on structure and properties of the new high-strength steel with increased cold resistance. CIS Iron and Steel Review. 2020. Vol. 20. pp. 50–54.
7. Poletskov P. P., Kuznetsova A. S., Alekseev, D. Yu. et al. Analysis of global level of developments in the area of production of hot-rolled high-strength cold-resistance sheet metal with yield strength ≥ 600 N/mm2. Vestnik Magnitogorskogo gosudarstvennogo tekhnicheskogo universiteta im. G. I. Nosova. 2020. Vol. 18. No. 4. pp. 32–38.
8. High-strength steel Strenx with increased strength. Available at: https://www.ssab.ru/api/sitecore/Datasheet/GetDocument?productId=E2D2EBBB2A144717A0B40944BE5F9FFB&language=ru-RU
9. Gliner R. E. Developments in the field of production of highstrength sheet steel in Sweden (steel Domex, Docol, AHSS). Proizvodstvo prokata. 2009. No. 10. pp. 11–18.
10. Aldur® High-strength quenched and tempered fine-grained steels. Available at: https://www.voestalpine.com/stahl/en/content/download/4495/file/Grobblech_TLB_ALDUR%20500-960_DE_0816.pdf
11. Wear-resistant steels for mining of raw materials: [brief report; steels of Dillidur 450 V and Dillimax 690 E grades for metallurgical equipment]. Chernye metally. 2014. No. 3. pp. 102–103.
12. New high-strength structural steel of Ruukki: [brief report; steel of Optim 700 MC Plus grade, Finland]. Chernye metally. 2011. No. 1. pp. 6–7.
13. Porter L. F., Rathbone A. M., Rolfe S. T., Dorshu K. E. Base Materials for Critical Application: requirements for Low Alloy Steel Plate, Forgings, Castings, Shapes, Bars, and Heads of HY 80/100/130 and HSLA 80/100. US Navy, Naval Sea Systems Command, NAVSEA Technical Publication T9074-BD-GIB-010/0300. Original 2002. August. Revision 2. 2012. December. 228 p.
14. Hot-rolled products from structural steel. Part. 6. Technical specification for delivery of flat products made of structural steel with high yield strength, in quenched and tempered state. BS EN 10025-6:2019.
15. Khotinov V. A., Farber V. M. Plasticity evaluation for structural steels by parameters of the uniform stage of extension curve. Materialovedenie. 2021. No. 1. pp. 24–31.
16. Klimashin S. I. Influence of heat treatment on martensite morphology and evolution of defect structure in cast medium-alloyed structural steel. Dissertation for Cand. Eng. Novokuznetsk. 2006. 197 p.
17. Golosienko S. A., Motovilina G. D., Khlusova E. I. Influence of structure formed during quenching on properties of high-strength cold-resistance steel after tempering. Voprosy materialovedeniya. 2008. No. 1 (53). pp. 32–44.
18. Shilyaev P. V., Bogach D. I., Krasnov M. L. et al. Mechanical properties and structural state of rolled sheet made of high-strength wearresistant weldable steel H500 MAGSTRONG. Metallovedenie i termicheskaya obrabotka metalov. 2020. No. 11 (785). pp. 8–12.
19. Andrews C., Dyson D., Keoun S. Electron diffraction patterns and their interpretation. Moscow: Mir. 1971. 256 p.
20. Goldshtein M. I., Farber V. M. Dispersion strengthening of steels. Moscow: Metallurgiya. 1979. 208 p.

Полный текст статьи Study of structure of high-strength cold-resistant steel after quenching and tempering
Назад