Журналы →  Chernye Metally →  2021 →  №12 →  Назад

Steelmaking and Foundry production
Название Improvement of the technology for railway wheel steel vacuum processing
DOI 10.17580/chm.2021.12.06
Автор A. N. Shapovalov, S. P. Nefedyev, S. I. Platov, M. V. Kharchenko
Информация об авторе

Novotroitsk branch of NUST MISIS (Novotroitsk, Russia):

A. N. Shapovalov, Cand. Eng., Professor, Head of the Dept. of Metallurgical Technologies and Equipment


Nosov Magnitogorsk State Technical University (Magnitogorsk, Russia):
S. P. Nefedyev, Cand. Eng., Senior Researcher, Research and Innovation Sector
S. I. Platov, Dr. Eng., Professor, Head of the Dept. of Machines and Technologies for Metal Forming and Mechanical Engineering
M. V. Kharchenko, Cand. Eng., Associate Professor, e-mail: kharchenko.mv@bk.ru


The analysis of data on the production of wheel steel grades “2” and “T” according to GOST 10791-2011 in the conditions of the of the electric furnace shop of Ural Steel JSC is presented. The content of hydrogen and nitrogen is significantly less than the regulated ones on most heats, which indicates an irrational vacuum mode. Such modes lead to an increase in energy costs for redistribution. All this testifies to the available reserves for improving the vacuum technology. As a result of research, it has been determined that in order to guarantee the production of hydrogen content less than 1.5 ppm and nitrogen up to 0.007 %, it is necessary to carry out vacuum treatment of steel at a residual pressure in a vacuum chamber of up to 3 mbar, the duration of processing in a high vacuum is at least 20 minutes, and argon consumption is blowdown not less than 0.05 m3/t, metal overheating from 110 to 130 °С. The overheating range of the steel before the start of the vacuum treatment the optimal temperature conditions for casting the steel. The optimum temperature of metal overheating at the beginning of processing on steel degassing installation is ~ 115-125 °C with a duration of vacuum treatment of 50-55 minutes (loss of metal temperature 70-75 °C), with overheating of the metal in a steel-pouring ladle before the start of casting 35-45 °C and at loss of metal temperature during transportation to casting 5 °C (15 min). Regression equations are obtained that allow predicting the results of degassing, as well as selecting the values of the vacuum treatment parameters in order to achieve a given content of dissolved gases – hydrogen ([H], ppm) and nitrogen ([N], %).
The research was conducted under financial support of the RF Ministry on Science and Higher Education (PROJECT No. FZRU-2020-0011).

Ключевые слова Vacuum treatment, vacuum tank degasser, railway wheel steel, duration of deep vacuum, vacuum chamber pressure, metal overheating temperature, argon consumption
Библиографический список

1. GOST 10791–2011. All-rolled wheels. Specifications. Moscow: Standartinform. 2011. 32 p.
2. Kudrin V. А. Theory and technology of steel production: Textbook for universities. Moscow: Mir, Izdatelstvo AST. 2003. 528 p.
3. Povolotskiy D. Ya., Kudrin V. А., Vishkarev А. F. Ladle furnace steel processing: Textbook for universities. Moscow: MISiS.1995. 256 p.
4. Morozov А. N., Strekalovskiy М. М., Chernov G. I., Katsnelson Ya. Е. Ladle furnace degassing of steel. Moscow: Metallurgiya. 1975. 288 p.
5. Brovman М. Ya. Continuous casting of metals. Moscow: EKOMET. 2007. 484 p.
6. Parshin V. М., Bulanov L. V. Continuous casting of steel. Lipetsk : PJSC NLMK. 2011. 221 p.
7. Pan H. Control Technology of Internal Quality for CC Billet. Advanced Materials Research. 2012. Vol. 415–417. pp. 1729–1734.
8. Shevchenko Е. А., Stolyarov А. М., Shapovalov А. N., Baranchikov К. V. Study of the cross-section distortion of a continuously cast slab. Izvestiya vuzov. Chernaya metallurgiya. 2014. No. 1. pp. 34–37.
9. Yu S., Miettinen J., Shao L., Louhenkilpi S. Mathematical Modeling of Nitrogen Removal from the Vacuum Tank Degasser. Steel Research International. 2015. Vol. 86. Iss. 5. pp. 466–477.
10. Fruehan R. J. Fundamentals and Practice for Producing Low Nitrogen Steels. ISIJ International. 1996. Vol. 36. pp. S58–S61.
11. Knupel H. Deoxidation and Vacuum Processing of Steel Melts. Vol. 1. Thermodynamic and Kinetic Basics: Translated from German. Moscow: Metallurgiya. 1973. 312 p.
12. Yu S., Miettinen J., Louhenkilpi S. Modeling Study of Nitrogen Removal from the Vacuum Tank Degasser. Steel Research International. 2014. Vol. 85. Iss. 9. pp. 1393–1402.

13. Karouni F., Wynne B. P., Talamantes‐Silva J., Phillips S. Modeling the Effect of Plug Positions and Ladle Aspect Ratio on Hydrogen Removal in the Vacuum Arc Degasser. Steel Research International. 2018. Vol. 89. Iss. 5. p. 1700551.
14. Yu S., Miettinen J., Louhenkilpi S. Numerical Study on the Removal of Hydrogen and Nitrogen from the Melt of Medium Carbon Steel in Vacuum Tank Degasser. Materials Science Forum. 2013. Vol. 762. pp. 253–260.
15. Nikolaev А. О., Bigeev V. А., Nikolaev О. А., Chigasov D. К. Features of degassing of pipe steel grades in conditions of the OCS of OJSC MMK. Elektrometallurgiya. 2013. No. 4. pp. 19–24.
16. Kushnarev А. V. Quality improvement of continuously cast billets of wheel steel manufactured at JSC “EVRAZ NTMK”. Chernye Metally. 2014. No. 3. pp. 28–32.
17. Kushnarev А. V., Bogatov А. А., Kirichkov А. А., Puzyrev S. S. Development of the technology for production of railway wheels. Vestnik Magnitogorskogo gosudarstvennogo tekhnicheskogo universiteta imeni G. I. Nosova. 2016. Vol. 14. No. 1. pp. 59–68.
18. Zinchenko S. D., Filatov М. V., Efimov S. V., Dub А. V., Goshkaderya S. V. Technological aspects of hydrogen removal using a ladle steel vacuuming unit. Metallurg. 2004. No. 11. pp. 41–42.
19. Tutarova V. D., Shapovalov А. N., Kalitaev А. N. Regularities of hydrogen removal in a chambertype steel degassing unit. Izvestiya vuzov. Chernaya metallurgiya. 2017. Vol. 60. No. 3. pp. 192–199.
20. Tutarova V. D., Shapovalov A. N., Kalitaev A. N. Objective Laws of Nitrogen Removal in the Vacuum Tank Degasser. Materials Science Forum. 2020. Vol. 989. pp. 381–387.
21. Smirnova E. A., Eliseeva I. A., Shapovalov A. N. The Degassing Laws for Railway Wheel Steel in a Vacuum Tank Degasser. Defect and Diffusion Forum. 2021. Vol. 410. pp. 269–274.
22. Zhitlukhin Е. G., Meling V. V., Dresvyankina L. Е., Gudov А. G., Stepanov I. А. Mastering and increasing the efficiency of steel degassing technology. Stal. 2014. No. 6. pp. 12–14.
23. Jauhiainen A., Jonsson L., Jönsson P., Eriksson S. The influence of stirring method on hydrogen removal during ladle treatment. Steel Research. 2002. Vol. 73. Iss. 3. pp. 82–90.
24. Steneholm K., Andersson M., Tilliander A., Jönsson P. G. Removal of hydrogen, nitrogen and sulphur from tool steel during vacuum degassing. Ironmaking & Steelmaking. 2013. Vol. 40. Iss. 3. pp. 199–205.
25. Socalici A., Popa E., Heput T., Dragoi F. Researches Regarding the Improvement of the Steel Quality. Solid State Phenomena. 2014. Vol. 216. pp. 273–278.
26. Ardelean E., Hepuț T., Vătășescu M., Crișan E. Researches Regarding the Influence of Vacuum Parameters on the Efficiency of Gas Removal from the Liquid Steel. Solid State Phenomena. 2016. Vol. 254. pp. 218–223.
27. Burgmann W., Davene J. The cost structure of vacuum steel degassing including ladle furnace treatment. Chernye Metally. 2012. No. 11. pp. 41–49.
28. Baskakova N. Т., Pesin I. А. Conceptual approaches in the optimization planning of equipment repairs at a metallurgical enterprise. Vestnik Magnitogorskogo gosudarstvennogo tekhnicheskogo universiteta imeni G. I. Nosova. 2013. Vol. 41. No. 1. pp. 93–96.

Language of full-text русский
Полный текст статьи Получить