Журналы →  Eurasian Mining →  2022 →  №1 →  Назад

EQUIPMENT AND MATERIALS
Название Substantiation of parameters and efficiency of sandwich belt high angle conveyors for deep open pit mines
DOI 10.7580/em.2022.01.13
Автор Sheshko E. E., Galkin V. I.
Информация об авторе

National University of Science and Technology—NUST MISIS, Moscow, Russia:

Sheshko E. E., Professor, Candidate of Engineering Sciences, esheshko@mail.ru
Galkin V. I., Professor, Doctor of Engineering Sciences

Реферат

The article focuses on substantiation of such parameters of heavy-duty sandwich belt high angle conveyors as the belt width to ensure operation without spillage of load, and the hugging pressure with regard to its dependence on the angle and length of the conveyor. It is noted that incorrect estimation of these parameters can lead to the redistribution of forces between the conveying and hugging belts with increasing load applied on the conveying belt. The economic efficiency of the high angle conveyors is considered in comparison to the traditional belt conveyors. It is shown that the cost of a traditional belt conveyor jumps with the increasing height of hoist. It is shown that the operating costs of the sandwich belt high angle conveyors increase almost linearly with an increase in the hoisting height and very slightly depend on the conveyor angle.

Ключевые слова Sandwich belt high angle conveyors, productivity, hugging pressure, belt width, spillage, installation angle, investment index
Библиографический список

1. Dmitriev V. G., Verzhansky A. P. Fundamentals of the theory of belt conveyors. Moscow : Gornaya kniga, 2017. 568 p.
2. Verzhansky A. P., Dmitriev V. G. Special belt conveyors. Ser.: Gornoe mashinostroenie. Moscow : Gornaya kniga, 2019. 496 p.
3. Anistratov Yu. N. et al. Open-pit mining of XXI century. Handbook. Moscow : Sistema maximum, 2019. Vol. 1. 645 p.
4. Sanakulov K. S., Umarov F. Ya., Shemetov P. A. Cost reduction in deep open pit mines based on the use of a high angle conveyor as part of in-pit crushing and conveying complex. Gornyi vestnik Uzbekistana. 2012. No. 2. pp. 8–12.
5. Semenkin A. V., Zhuravlev A. G. Forecast of comparative areas of high-angle conveyors. GIAB. 2021. No. 5–2. pp. 322–337.
6. Dos Santos J. D. The cost and value of high-angle conveying: A comparison of economics for different conveying paths. Bulk Solids Handling. 2013. Vol. 33, No. 1. pp. 18–23.
7. Sandwich Belt High Angle Conveyor for Mining & In Pit Crushing Conveying : project. 2017. Available at: https://bevconwayors.com/product/sandwich-belt-high-angle-conveyor-for-miningin-pit-crushing-conveying/ (accessed: 16.03.2022).
8. Dos Santos J. A. High Angle Conveying: The Vital (missing) Link to IPCC Systems–2017. Bulk Solids Handling. 2017. Vol. 37, No. 1. pp. 16–26.
9. Sheshko E. E., Kuryatnikov A. V., Shulyatev B. I. et al. Experimental determination of pressure exerted by load on pressure belt of high-angle conveyor. Open Pit Coal Mining : Collected Works. Moscow : Nedra, 1975. Iss. 2.
10. Sheshko E. E. Influence of hold-down on operability and basic parameters of high-angle pressure belt conveyor. Gornyi Zhurnal. 2019. No. 4. pp. 69–73. DOI: 10.17580/gzh.2019.04.15
11. Sheshko E. E., Pestrikov O. V. Justification of the required holddown dependence on the length and angle of high-angle pressure belt conveyor. Gornyi Zhurnal. 2021. No. 5. pp. 83–86. DOI: 10.17580/gzh.2021.05.10
12. Kartavyi A. N. Prospects for the use of sandwich belt high angle conveyors at In Pit Crushing Conveying. Gornyi Zhurnal. 2003. No. 6. pp. 52–56.
13. Atakulov L. N., Toshev Zh. B., Kakharov S. K. et al. Detection technique for jointing tears of steel-cable rubber belts. Gornyi vestnik Uzbekistana. 2018. No. 3(74). pp. 61–65.
14. Atakulov L. N., Kakharov S. K., Khalikov U. R. Factors affecting the performance of the high angle conveyor KNK-270 and the reasons for its downtime. Gorniy vestnik Uzbekistana. 2018. No. 1(72). pp. 67–70.
15. Atakulov L. N., Sheshko O. E. Improvement of economic efficiency of the high-angle conveyor KNK-270 at Navoi Mining and Metallurgical Combinat. GIAB. 2019. No. 5. pp. 181–188.

Полный текст статьи Substantiation of parameters and efficiency of sandwich belt high angle conveyors for deep open pit mines
Назад