Journals →  Non-ferrous Мetals →  2022 →  #2 →  Back

MATERIALS SCIENCE
ArticleName X-ray computed tomography of cast metal matrix composites
DOI 10.17580/nfm.2022.02.14
ArticleAuthor Prusov E. S., Deev V. B., Ri E. H.
ArticleAuthorData

Vladimir State University named after Alexander and Nikolay Stoletovs, Vladimir, Russia:

E. S. Prusov, Associate Professor, Department of Functional and Constructional Materials Technology, e-mail: eprusov@mail.ru

 

Wuhan Textile University, Wuhan, China1 ; National University of Science and Technology “MISiS”, Moscow, Russia2:

V. B. Deev*, Professor, Professor of the School of Mechanical Engineering and Automation1, Chief Researcher of the Laboratory “Ultrafine-Grained Metallic Materials”2, e-mail: deev.vb@mail.ru

 

Pacific National University, Khabarovsk, Russia:
E. H. Ri, Professor, Head of the Department of Foundry Engineering and Metal Technology, e-mail: erikri999@mail.ru


*Correspondence author.

Abstract

The development of new cast metal matrix composites and technological processes for their production are inextricably linked with the need to improve the methods of quantitative non-destructive testing. In this work, the features of the spatial structure of cast in-situ metal matrix composites (on example of the Al – Mg2Si system) were studied using X-ray computed microtomography. The parameters of tomographic scanning were optimized to identify structural components with close ranges of radioparency. The rational selection of the scanning parameters of the samples made it possible, during the subsequent computer processing of the slice sets, to clearly identify the structural constituents of the metal matrix composites depending on the gray levels in their comparison with the characteristic morphology of the observed constituents (primary Mg2Si crystals, pseudobinary eutectic, compounds of impurity elements). The total volume of porosity in the studied samples of Al + 15 wt.% Mg2Si composites after melt thermal-rate treatment at 900 °C did not exceed 0.05 mm3, which corresponds to a porosity content in the sample of 0.13 vol.%. The presented results show the significant potential of tomography in the study of the structural and morphological characteristics of composite materials and internal defects in cast products made from them.

This research was funded by the Russian Science Foundation (Project № 20-19-00687).

keywords Cast metal matrix composites, X-ray computed tomography, selection of scanning parameters, identification of structural constituents, internal defects, quantitative analysis
References

1. Dun Y., Wang S.-J., Shi X.-H., Zhou Z.-Y. Nonlinear Ultrasonic Techniques for Testing Micro-Defects in Metal Matrix Composite Structure. Key Engineering Materials. 2011. Vol. 483. pp. 784–788.
2. Mathew J., Mandal A., Warnett J., Williams M. A., Chakraborty M., Srirangam P. X-Ray Tomography Studies on Porosity and Particle Size Distribution in Cast in-situ Al – Cu – TiB2 Semi-Solid Forged Composites. Materials Characterization. 2016. Vol. 118. pp. 57–64.
3. Park B., Lee D., Jo I., Lee S. B., Lee S. K., Cho S. Automated Quantification of Reinforcement Dispersion in B4C/Al Metal Matrix Composites. Composites Part B: Engineering. 2020. Vol. 181. 107584.
4. Prusov E., Kechin V. General Concept of Cast Metal Matrix Composites Design. World Foundry Congress “Creative Foundry”, WFC 2018 – Proceedings, Krakow. 2018. pp. 199–200.
5. Gawdzinska K. Quality Features of Metal Matrix Composite Castings. Archives of Metallurgy and Materials. 2013. Vol. 58, Iss. 3. pp. 659–662.
6. Shabani M. O., Mazahery A. Suppression of Segregation, Settling and Agglomeration in Mechanically Processed Composites Fabricated by a Semisolid Agitation Processes. Transactions of the Indian Institute of Metals. 2013. Vol. 66, Iss. 1. pp. 65–70.
7. Dong P.-Y., Zhao H.-D., Chen F.-F., Li J.-W. Microstructures and Properties of A356–10%SiC Particle Composite Castings at Different Solidification Pressures. Transactions of Nonferrous Metals Society of China. 2013. Vol. 23, Iss. 8. pp. 2222–2228.
8. Gawdzinska K., Grabian J., Przetakiewicz W. Use of X-ray Radiography in Finding Defects in Metal-Matrix Composite Casts. Metalurgija. 2008. Vol. 47, Iss. 3. pp. 199–201.
9. Huang Y. D., Froyen L., Wevers M. Quality Control and Nondestructive Tests in Metal Matrix Composites. Journal of Nondestructive Evaluation. 2001. Vol. 20, Iss. 3. pp. 113–132.
10. Nicoletto G., Anzelotti G., Konecná R. X-ray Computed Tomography vs. Metallography for Pore Sizing and Fatigue of Cast Al-alloys. Procedia Engineering. 2010. Vol. 2, Iss. 1. pp. 547–554.
11. Yang Z., Maurey A., Kang J., Wilkinson D. S. 2D and 3D Characterization of Pore Defects in Die Cast AM60. Materials Characterization. 2016. Vol. 114. pp. 254–262.
12. Ohser J., Schladitz K. 3D Images of Materials Structures: Processing and Analysis. Wiley-VCH Verlag GmbH & Co. KgaA, Wienheim, 2009. 341 p.
13. Maire E., Buffière J. Y., Salvo L., Blandin J. J., Ludwig W., Létang J. M. On the Application of X-ray Microtomography in the Field of Materials Science. Advanced Engineering Materials. 2001. Vol.3, Iss. 8. pp. 539–546.
14. Salvo L., Suéry M., Marmottant A., Limodin N., Bernard D. 3D Imaging in Material Science: Application of X-ray Tomography. Comptes Rendus Physique. 2010. Vol. 11, Iss. 9–10. pp. 641–649.
15. Maire E., Withers P. J. Quantitative X-ray Tomography. International Materials Reviews. 2014. Vol. 59, Iss. 1. pp. 1–43.
16. Deev V. B., Prusov E. S., Ri E. H. Physical Methods of Processing the Melts of Metal Matrix Composites: Current State and Prospects. Russian Journal of Non-Ferrous Metals. 2022. Vol. 63, Iss. 3. pp. 292–304.
17. Prusov E., Deev V., Rakhuba E. Effect of Superheat Melt Treatment on Structure and Mechanical Properties of in-Situ Aluminum Matrix Composites. METAL 2018 – 27th International Conference on Metallurgy and Materials, Conference Proceedings. 2018. pp. 1358–1362.
18. Prusov E. S., Aborkin A. V., Deev V. B., Ri E. K., Rakhuba E. M. Structural and Morphological Characteristics of the Friction Surfaces of in-Situ Cast Aluminum Matrix Composites. Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques. 2021. Vol. 15, Iss. 6. pp. 1332–1337.
19. Ghiasinejad J., Emamy M., Ghorbani M. R., Malekan A. Wear Behavior of Al – Mg2Si Cast In-situ Composite: Effect of Mg2Si Different Volume Fractions. AIP Conference Proceedings. 2010. Vol. 1252. 1012.
20. Prusov E. S., Shabaldin I. V., Deev V. B. Quantitative Characterization of the Microstructure of in Situ Aluminum Matrix Composites. Journal of Physics: Conference Series. 2021. Vol. 2131. 042040.
21. Tolnai D., Requena G., Cloetens P., Lendvai J., Degischer H. P. Effect of Solution Heat Treatment on the Internal Architecture and Compressive Strength of an AlMg4.7Si8 Alloy. Materials Science and Engineering A. 2013. Vol. 585. pp. 480–487.
22. Kastner J., Plank B., Requena G. Non-Destructive Characterisation of Polymers and Al-alloys by Polychromatic Cone-Beam Phase Contrast Tomography. Materials Characterization. 2012. Vol. 64. pp. 79–87.
23. Soleymani Shishvan S., Asghari A.-H. Effects of Particle Shape and Size Distribution on Particle Size-Dependent Flow Strengthening in Metal Matrix Composites. Scientia Iranica. 2017. Vol. 24, Iss. 3. pp. 1091–1099.
24. Zewail A.H. 4D Visualization of Matter: Recent Collected Works. Imperial College Press, London, 2014. 409 p.
25. Daudin R., Terzi S., Lhuissier P., Salvo L., Boller E. Remelting and Solidification of a 6082 Al Alloy Containing Submicron Yttria Particles: 4D Experimental Study by in Situ X-ray Microtomography. Materials and Design. 2015. Vol. 87. pp. 313–317.
26. Sillekens W. H., Casari D., Mirihanage W. U., Terzi S., Mathiesen R. H., Salvo L., Daudin R., Lhuissier P., Guo E., Lee P. D. The Use of In Situ X-ray Imaging Methods in the Research and Development of Magnesium-Based Grain-Refined and Nanocomposite Materials. 2016. JOM. Vol. 68, Iss. 12. pp. 3042–3050.
27. Chen Y., Shi Y., Chateau C., Marrow J. In Situ X-ray Tomography Characterization of 3D Deformation of C/C-SiC Composites Loaded Under Tension. Composites Part A: Applied Science and Manufacturing. 2021. Vol. 145. 106390.

Full content X-ray computed tomography of cast metal matrix composites
Back