National Research Tomsk State University, Tomsk, Russia:

V. D. Valikhov, Research Engineer at the High-Energy and Special Materials Research Laboratory, e-mail: valihov.snobls@gmail.com
I. A. Zhukov, Head of the Laboratory for Metallurgy Nanotechnologies, Doctor of Technical Sciences
N. I. Kakhidze, Research Engineer at the Laboratory for Metallurgy Nanotechnologies
D. A. Tkachev, Junior Researcher at the Laboratory for Metallurgy Nanotechnologies

This paper looks at a composite material based on Al – Si alloy of grade AК9 that was produced by mechanical stirring and reinforced with 1 and 2 wt % of basalt fibres. The paper describes the results of a study that looked at the structure and phase composition of the basalt fibres introduced. It is shown that heat treating basalt fibres at the temperatures of up to 600 oC does not change their phase composition. The authors examine the microstructures of the initial cast alloy AK9 and the alloy reinforced with basalt fibres; look at the relationship between the structure obtained after introduction of basalt fibres and the physical and mechanical properties of the alloy; carried out a fractography study of the fracture surface in reinforced alloy specimens following a series of tensile tests. The authors analyzed how reinforcing effect is achieved when basalt fibres are introduced in the aluminium alloy AK9. The experimental data indicate that the introduction of basalt fibres in the aluminium matrix significantly enhances the mechanical performance of the alloy compared with the initial alloy AK9. Thus, the tensile strength and ultimate strength rise by 40 to 55 % compared with the initial alloy, whereas the hardness rises by 20 to 35 % depending on the weight fraction of basalt fibres in the alloy.
This research was funded by the Ministry of Education and Science of the Russian Federation under Governmental Assignment No. FSWM-2020-0028. The studies (optical and electron microscopy, tensile tests, hardness and microhardness tests, study of phase composition) were carried out using the facilities of the Tomsk Regional Shared Knowledge Centre, a part of the National Research Tomsk State University. Support for the Centre is provided by the Ministry of Higher Education and Science of the Russian Federation under Grant No. 075-15-2021-693 (No. 13.ЦКП.21.0012).

1. Poznak A., Freiberg D., Sanders P. Automotive wrought aluminium alloys. Fundamentals of Aluminium Metallurgy. Elsevier, 2018. pp. 333–386.
2. Rambabu P. et al. Aluminium alloys for aerospace applications. Aerospace Materials and Material Technologies. Singapore : Springer Singapore, 2017. pp. 29–52.
3. Javidani M., Larouche D. Application of cast Al – Si allo ys in internal combustion engine components. International Materials Reviews. 2014. Vol. 59, No. 3. pp. 132–158.
4. Robles Hernandez F. C., Herrera Ramírez J. M., Mackay R. Erratum to: Al – Si alloys: automotive, aeronautical, and aerospace applications. Al – Si alloys. Cham : Springer International Publishing, 2017. pp. E1–E1.
5. Dong Z. Q. Effect of short T6 heat treatment on the thermal conductivity and mechanical properties of different casting processes Al – Si – Mg – Cu alloys. Metals. 2021. Vol. 11, Iss. 9. 1450.
6. Chelladurai S. J. S. et al. Investigation of mechanical properties and dry sliding wear behaviour of squeeze cast LM6 aluminium alloy reinforced with copper coated short steel fibres. Transactions of the Indian Institute of Metals. 2018. Vol. 71, No. 4. pp. 813–822.
7. Vorozhtsov S. et al. Influence the carbon nanotubes on the structure and mechanical properties of aluminum-based metal matrix composites. AIP Conference Proceedings. 2016. Vol. 1772, Iss. 1. 030021.
8. Agureev L. E. et al. Development of heat resistant aluminum composite with minor addition of alumina nanofibres (NafenTM). Inorganic Materials: Applied Research. 2020. Vol. 11, No. 5. pp. 1045–1050.
9. Malaki M. et al. Advanced metal matrix nanocomposites. Metals. 2019. Vol. 9, No. 3. 330.
10. Adole O. et al. Fibre/matrix intermetallic phase formation in novel aluminium-basalt composites. Materials Letters. 2019. Vol. 239. pp. 128–131.
11. Colombo C., Vergani L., Burman M. Static and fatigue characterisation of new basalt fibre reinforced composites. Composite Structure. 2012. Vol. 94, No. 3. pp. 1165–1174.
12. Militky J., Kovacic V. Ultimate mechanical properties of basalt filaments. Textile Research Journal. 1996. Vol. 66, Iss. 4. pp. 225–229.
13. Zhiming Y. et al. Investigation on mechanical properties and failure mechanisms of basalt fibre reinforced aluminum matrix composites under different loading conditions. Journal of Composite Materials. 2018. Vol. 52, No. 14. pp. 1907–1914.
14. Sreenatha Reddy S., Dhanasekaran R. Effect of fly ash and basalt on wrought and cast aluminum alloy. Materials Today. 2018. Vol. 5, No. 13. pp. 27112– 27117.
15. Brainard Abraham C. et al. Basalt fibre reinforced aluminium matrix composites – A review. Materials Today. 2020. Vol. 21. pp. 380–383.
16. Vorozhtsov A. B., Dammer V. Kh., Arkhipov V. A., Zhukov I. A. et al. Device for mixing light metal melts with micropowders of refractory particles and fibres. Patent RF, No. 2758953. Applied: 10.03.2021. Published: 03.11.2021.
17. GOST 1497–84. Metals. Methods of tension test. Introduced: 01.01.1986.
18. GOST 9450–76. Measurements microhardness by diamond instruments indentation. Introduced: 01.01.1977.
19. GOST 9012–59. Metals. Method of Brinell hardness measurement. Introduced: 01.01.1960.
20. Wu Z. et al. Mineral fibres: basalt handbook of natural fibres. Woodhead Publishing, 2020. pp. 433–502.
21. Zhang L. et al. Formation of microstructure in Al – Si alloys under ultrasonic melt treatment. Light metals 2012. Cham : Springer, 2012. pp. 999–1004.
22. Boettinger W. J. Solidification microstructures: recent developments, future directions. Acta materialia. 2009. Vol. 57, Iss. 4. pp. 941–971.
23. Mazahery A., Shabani M. O. Plasticity and microstructure of A356 matrix nano composites. Journal of King Saud University-Engineering Sciences. 2013. Vol. 25, No. 1. pp. 41–48.
24. Kaptay G. Interfacial criterion of spontaneous and forced engulfment of reinforcing particles by an advancing solid/liquid interface. Metallurgical and Materials Transactions A. 2001. Vol. 32, No. 4. pp. 993–1005.
25. Uhlmann D. R., Chalmers B., Jackson K. A. Interaction between particles and a solid-liquid interface. Journal of Applied Physics. 1964. Vol. 35, No. 10. pp. 2986–2993.
26. Dai L. H., Ling Z., Bai Y. L. Size-dependent inelastic behavior of particle-reinforced metal – matrix composites. Composites Science and Technology. 2001. Vol. 61, No. 8. pp. 1057–1063.
27. Fan C. et al. Microstructures and mechanical properties of BP/7A04 Al matrix composites. Transactions of Nonferrous Metals Society of China. 2019. Vol. 29, No. 10. pp. 2027–2034.