Journals →  Chernye Metally →  2023 →  #3 →  Back

Foundry Production
ArticleName Optimization of chemical composition of cast iron molds. Part 3
DOI 10.17580/chm.2023.03.03
ArticleAuthor V. A. Gulevsky, S. N. Tsurikhin, N. Yu. Miroshkin, N. A. Kidalov
ArticleAuthorData

Volgograd Industrial College, Volgograd, Russia:

V. A. Gulevsky, Cand. Eng., Lecturer, e-mail: gulevskiy.v@mail.ru

 

Volgograd State Technical University, Volgograd, Russia:
S. N. Tsurikhin, Cand. Eng., Associate Prof., Dept. of Machinery and Technology of Foundry Production
N. Yu. Miroshkin, Head of Laboratory, Dept. of Machinery and Technology of Foundry Production
N. A. Kidalov, Dr. Eng., Prof., Head of the Dept. of Machinery and Technology of Foundry Production

Abstract

The heavy mode of operation of the mills (high heating temperature, their installation on mobile and stationary ditches, intensive cargo flows, etc.) imposes strict requirements on the material from which it is made and the technology of its production. In the conditions of foundry production, there are various chemical compositions of molds, which is why their durability may change during operation. Increasing the durability of scissors has a positive effect on production efficiency. The chemical composition of cast iron can determine the durability of the molds. It is necessary to choose the optimal chemical composition of cast iron in the manufacture of molds to increase the filling. Obtaining a mold in the foundry and metallurgy with optimal properties is a complex multi–criteria task that is solved using the theory of quality. This will significantly reduce the duration of the experiment to optimize the chemical composition of cast iron, when modifying it or changing the design of the samples. To optimize the chemical composition of the molds and increase their durability, mathematical modeling was applied, which shows the optimal chemical composition with their maximum durability. It has been experimentally established that the durability of scissors depends on the carbon content, to a lesser extent on the chromium and phosphorus content. Practically, the resistance of the eyelashes is less affected by the boundaries of changes in the content of manganese and sulfur. It is possible to obtain the necessary physical, mechanical and technological properties and improve the durability of the molds by reducing the amount of sulfur and phosphorus in the composition of the initial cast iron or by introducing new technological additives - modifiers, but at the same time the properties of the cast iron of the molds change significantly. 

keywords Cast iron, chemical composition, mould resistance, multi-criteria optimization, cupola smelters, foundry production, physical and mechanical properties, averaging functions, technological properties, limitations of the values of properties
References

1. Kuksa А. V. Cast iron casting molds. Moscow: Metallurgiya, 1989. 152 p.
2. Kabnure B. B., Shinde V. D., Patil D. C. Quality and yield improvement of ductile iron casting by simulation technique. Mater. Today Proc. 2020. Vol. 27. pp. 111–116. DOI: 10.1016/j.matpr.2019.09.022
3. Lacaze J., de la Torre U., Sertucha J., Regordosa A. Modelling of compacted graphite cast iron solidification – discussion of microstructure parameters. China Foundry. 2020. Vol. 17, Iss. 2. pp. 144–149. DOI: 10.1007/s41230-020-0050-2
4. Mendakiewicz J. Experimental verification of the cast iron solidification model. Arch Foundry Eng. 2022. Vol. 22, Iss. 3. pp. 91–94. DOI: 10.24425/afe.2022.140240
5. Çolak M., Şekerden M. Modelling and validation of effect of binder type on feeding behaviour of spheroidal graphite cast iron. Int. J. Cast. Metals Res. 2022. Vol. 35, Iss. 1-3. pp. 9–16. DOI: 10.1080/13640461.2022.2064653
6. Milyaev A. F., Nikitin Yu. P., Kadnikov S. V., Timofeev V. A., Matveev A. N. Influence of the chemical composition of cupola iron on the durability of molds. Teoriya i tekhnologiya metallurgicheskogo proizvodstva. 2014. No. 1 (14). pp. 56–58.
7. Milyaev A. F., Nikitin Yu. P., Kadnikov S. V., Timofeev V. A., Matveev A. N. Influence of operating parameters on the durability of cupola iron molds. Liteynoe proizvodstvo. 2014. No. 2 (15). pp. 77–80.
8. Gulevskiy V. A., Tsurikhin S. N., Gulevskiy V. V., Miroshkin N. Yu. Investigation of the modification effect on performance properties of cast iron molds. Chernye Metally. 2021. No. 1. pp. 23–28.
9. Iohnson N., Leone F. Statistics and experimental design in engineering and the physical science. Moscow, 1981. 516 p.
10. Makarichev Yu. А., Ivannikov Yu. N. Methods of experiment planning and data processing: textbook. Samara: Samara Polytech. 2016. 131 p.
11. Izosimov V. A., Usmanov R. G., Kanafin M. N. Influence of the chemical composition of ductile iron on its mechanical properties. Liteynoe proizvodstvo. 2004. No. 6. pp. 2–5.
12. Dolinskiy Е. F. Processing of measurement results. Moscow, Izdatelstvo Standartov, 1973. 191 p.
13. Parfentyeva I. Е. Processing of measurement results: textbook. Moscow: Universitet mashinostroeniya, 2014. 132 p.
14. Draper N., Smith H. Applied regression analysis. Moscow: Izdatelskiy dom "Vilyams". 2007. 187 p.
15. Gulevskiy V. A., Tsurikhin S. N., Gulevskiy V. V., Miroshkin N. Yu. Investigation of the modification effect on performance properties of cast iron molds. Part 2. Chernye Metally. 2022. No. 3. pp. 20–26.
16. Saati T. L. Integral numerical optimizations methods and experimental problems which are connected with these methods. Moscow: Mir. 1973. 302 p.
17. Bryzgalin G. I. Introduction in the quality theory. Volgograd: Politekhnik. 1988. 91 p.
18. Kolmogorov А. N., Fomin S. V. Elements of the theory of functions and functional analysis. Moscow: Nauka, 1972. 496 p.
19. Orlov A. I. Econometrics. Textbook. Moscow: Izdatelstvo "Egzamen". 2002. 576 p.
20. Antsupov А. V. Modeling the processes of formation of failures of metallurgical machines. Magnitogorsk: Nosov Magnitogorsk State Technical University. 2021. 211 p.
21. Odinokov V. I., Dmitriev E. A., Evstigneev A. I., Sviridov A. V., Ivankova E. P. Modeling and optimization of the choice of material properties and structures of shell molds according to investment models. Izvestiya vyzov. Chernaya metallurgiya. 2020. Vol. 63. No. 9. pp. 742–754.
22. Gushchin V. N., Ulyanov V. А., Vasilyev V. А. Mathematical and physical modeling of thermophysical processes in metallurgy. N. Novgorod: NGTU, 2014. 155 p.
23. Ulyanov V. А., Sivkov V. A., Gushchin V. N. Physical modeling in the field of system analysis of metallurgical objects. N. Novgorod: NGTU, 2014. 317 p.
24. Tsymbal V. P. Mathematical modeling of complex systems in metallurgy. Kemerovo; Moscow: Izdatelskoe objedinenie "Rossiyskie universitety": Kuzbassvuzizdat – ASTSh, 2006. 431 p.
25. Yu Liu, Hao Qiu, Zixu He, Yue Yu, Heping Liu. A Study of Physical Modeling and Mathematical Modeling on Inclusion Behavior in a Planar Flow Casting Process. Metals. 2022, Vol. 12, Iss. 4. p. 606.
26. Zhongqiu Liu. Numerical modeling of metallurgical processes: continuous casting and electroslag remelting. Metals. 2022. Vol. 12, Iss. 5. p. 746.
27. Avakimov G. G. Physical modeling of processes and objects in metallurgy: course of lectures. Moscow: Universitet mashinostroeniya, 2014. 63 p.
28. Fedosov A. V., Chumachenko G. V., Khodarev M. A., Golomeev V. V. Evaluation of the effectiveness of the use of closed ingot top of various geometry based on the results of mathematical modeling. Izvestiya vysshikh uchebnykh zavedeniy. Chernaya metallurgiya. 2018. Vol. 61. No. 7. pp. 543–550.
29. Volokitina I. E., Naizabekov A. B., Volokitin A. V., Salko O. Y., Chigirinsky V. V., Panin E. A. Modelling of the new route drawing technology for a metal processing efficiency. Mathematical Modeling. 2022. Vol. 6, Iss. 3, pp. 82–83.
30. Çelik G. A., Tzini M.-I. T., Polat Ş., Atapek Ş. H., Haidemenopoulos G. N. Matrix design of a novel ductile cast iron modified by W and Al: A comparison between thermodynamic modeling and experimental data. Metallurgical and Materials Engineering. 2020. Vol. 1, Iss. 26. pp. 15–29. DOI: 10.30544/449

Language of full-text russian
Full content Buy
Back