Journals →  Chernye Metally →  2024 →  #2 →  Back

Sintering
ArticleName Intensification of the sintering process by rolling converter sludge onto the surface of pelletized charge granules
DOI 10.17580/chm.2024.02.02
ArticleAuthor V. G. Mikhailov, A. V. Karpov, A. A. Eremeev
ArticleAuthorData

Lipetsk State Technical University, Lipetsk, Russia

V. G. Mikhailov, Cand. Eng., Associate Prof., Dept. of Metallurgical Technologies, e-mail: valentinmikhailov@yandex.ru
A. V. Karpov, Cand. Eng., Associate Prof., Chair for Metallurgical Technologies, e-mail: antonkrpv@rambler.ru
A. A. Eremeev, Graduate Student, Dept. of Metallurgical Technologies

Abstract

Converter sludge is a by-product of steelmaking and is formed in quantities of 10–30 kg/t steel. This sludge can be considered as a valuable technogenic raw material for the production of cast iron and steel and can be used as iron flux in sintering, blast furnace and steelmaking processes, since the total content of Fetot and CaO is 65–80 %, while the mass fraction of SiO2 does not exceed 3 %. The reuse of converter sludge in metallurgical production is limited by the high zinc content (up to 4 %). The possibilities of involving converter sludge in recycling in metallurgical production are considered. The nature of the formation of converter sludge, its granulometric and mineralogical compositions are given. Examples of industrial implementation of technology for rolling various materials during the pelletizing process at sintering factories of domestic and foreign enterprises are shown. In laboratory conditions, a study was carried out of the effectiveness of rolling converter sludge (sludge was used after dehydration and drying, 26% of particles with a particle size of >2.5 mm), both separately and with additives onto the surface of pelletized granules. The sludge supply technology simulated the process of dosing it into the tail part of the pelletizing drum 30 s before the end of the pelletizing process. The greatest efficiency was achieved when using a mixture for rolling of converter sludge (75%), lime (15%) and coke (10%) in an amount of 9% of the total mass of the charge. The use of such a mixture made it possible to increase the productivity of the sintering process by 17.5% due to an increase in the vertical sintering rate, with a slight decrease in the yield of suitable agglomerate.

keywords Converter sludge, particle size distribution, chemical composition, fuel rolling, converter sludge rolling, sintering, productivity, zinc.
References

1. Bugakov M. N., Sebyakin S. V., Khaydukov V. P. Converter sludge as a metallurgical waste of double benefit. Stal. 2018. No. 9. pp. 73–76.
2. Korshikov G. V., Zevin S. L., Grekov V. V., Kuznetsov A. S. et al. Behavior of zinc during sintering of blast furnace and converter sludge with KMA concentrates. Stal. 2003. No. 5. pp. 2–6.
3. Mikhaylov V. G., Khaydukov V. P., Lupova I. A., Stepanov O. S. Use of ferritic-calcium material when melting carbon ferromanganese. Metallurgiya mashinostroeniya. 2009. No. 3. pp. 26, 27.
4. Kovalenko A. G., Zubenko A. V., Padalka V. P. et al. Introduction of technology for preparation of sludge with its subsequent use in the sinter charge at the Yenakievo Metallurgical Plant. Metallurg. 2021. No. 12. pp. 80–85.
5. Panishev N. V., Bigeev V. A., Chernyaev A. A. Processing of fine-grained waste from metallurgical production to produce granulated cast iron and extract zinc. Vestnik Magnitogorskogo gosudarstvennogo tekhnicheskogo universiteta imeni G. I. Nosova. 2013. No. 4 (33). pp. 26–29.
6. Anikin A. E., Galevsky G. V., Rudneva V. V. Study of technological modes for effective metallization of iron oxide-containing waste from metallurgical production. Izvestiya vuzov. Chernaya Metallurgiya. 2020. No. 63 (5). pp. 335–343.
7. Tleugabulov S. M., Aitkenov N. B., Koishina G. M. et al. Technology for producing ore-coal pellets from a mixture of converter and coal sludge and reduction smelting of steel. Stal. 2021. No. 1. pp. 78–80.
8. Shkoller M. B., Kazimirov S. A., Khodosov I. E. et al. Recycling of converter sludge based on moisture adsorption and coking with coals. Koks i khimiya. 2017. No. 2. pp. 38–44.
9. Toporkova Yu. I. Complex processing of zinc-containing dust from steelmaking in ammonia-chloride environments. Thesis of inauguration of Dissertation … of Candidate of Engineering Sciences. Yekaterinburg : Ural Federal University named after the first President of Russia B. N. Yeltsin, 2021. 23 p.
10. GOST 12764–73. Iron ores, concentrates, agglomerates and pellets. Method for determination of moisture. Introduced: 01.01.1974.
11. GOST 27562–87. Iron ores, concentrates, sinters and pellets. Determination of size distribution by sieving. Introduced: 01.07.1988.
12. Kelebek S., Yörük Seher, Davis Boyd. Characterization of basic oxygen furnace dust and zinc removal by acid leaching. Minerals Engineering. 2004. Vol. 17. pp. 285–291. DOI: 10.1016/j.mineng.2003.10.030
13. Anikin A. E., Galevsky G. V., Rudneva V. V. Study of physical and chemical characteristics of oxide-containing technogenic raw materials. Chernaya metallurgiya. Byulleten nauchnotekhnicheskoy i ekonomicheskoy informatsii. 2018. No. 9. pp. 107–112.
14. Katrenov B. B., Zhumashev K. Zh., Narembekova A. K., Karsenbekova L. A. Determination of optimal conditions for dezincification of converter production sludge using a hydrometallurgical method. Kompleksnoe ispolzovanie mineralnogo syrya. 2017. No. 1. pp. 64–70.
15. Khaidukov V. P. Theoretical and technological foundations for production of complex slagforming agents and their use in oxygen converter production. Thesis of inauguration of Dissertation … of Doctor of Engineering Sciences. Lipetsk : LSTU, 1996. 44 p.
16. Gushchin D. N., Chukin D. M., Frolov Yu. A. et al. Influence of lime distribution between the intermediate warehouse and the charging department of the MMK`s sinter factory No. 5. on agglomeration process. Chernaya metallurgiya. Byulleten nauchno-tekhnicheskoy i ekonomicheskoy informatsii. 2023. No. 2. pp. 95–106.
17. Hiroshi Ogi, Takayuki Maeda, Koichiro Ohno, Kazuya Kunitomo. Effect of coke breeze distribution on coke combustion rate of the quasi-particle. ISIJ International. 2015. Vol. 55, Iss. 12. pp. 2550–2555. DOI: 10.2355/isijinternational.ISIJINT-2015-089
18. Inazumi T. Latest advances in iron ore sintering technology. Novosti chernoy metallurgii za rubezhom. 1997. No. 4. pp. 8–18.
19. GOST 15137–77. Iron and manganese ores, agglomerates and pellets. Determination of tumbler strength. Introduced: 01.01.1978.
20. Kato Shinya, Oya Kenji, Higuchi Takahide, Hayasaka Yasukazu et al. Improvement of sinter productivity and quality. 6th International Congress on the Science and Technology of Ironmaking, Rio de Janeiro, 2012. pp. 1100–1112.
21. Lima A. J. A. S. Caracterização tecnológica de uma mistura de sinter feed e pellet feed para uso em processo HPS. Escola de Minas, Universidade Federal de Ouro Preto, Ouro Preto, 2019. 125 p.
22. Oyama Nobuyuki, SATO Hideaki, Takeda Kanji, Ariyama Tatsuro et al. Development of coating granulation process at commercial sintering plant for improving productivity and reducibility. ISIJ International. 2005. Vol. 45. pp. 817–826. DOI: 10.2355/isijinternational.45.817

Language of full-text russian
Full content Buy
Back