Журналы →  Tsvetnye Metally →  2024 →  №3 →  Назад

MATERIALS SCIENCE
Название Features of a weld pool crystallization during laser welding of copper and steel
DOI 10.17580/tsm.2024.03.07
Автор Kuryntsev S. V., Shiganov I. N.
Информация об авторе

Tupolev Kazan National Research Technical University – KAI, Kazan, Russia

S. V. Kuryntsev, Associate Professor of the Department of Materials Science, Welding and Industrial Safety, Candidate of Economic Sciences, e-mail: kuryntsev16@mail.ru


Bauman Moscow State Technical University, Moscow, Russia
I. N. Shiganov, Professor of the Department of Laser Technologies in Mechanical Engineering, Doctor of Technical Sciences

Реферат

The paper presents the results of studies on the crystallization features of a weld pool made of dissimilar alloys, M1 copper and 12Kh18N10T steel produced by laser welding. In addition to the previously conducted studies on the microstructure, mechanical and operational properties, the authors carried out studies on the microstructure of the top surface of the weld using optical and electron microscopy, and determined the point chemical composition of the differing microstructural components of the weld pool. It was revealed that in the left part of the weld pool, in the center of the grains, there are spherical depressions along the grain bounda ries, point precipitates in the center of the grains and elongated precipitates along the grain boundaries, which significantly differ in the chemical composition. Point and elongated areas contain significantly more copper (18–24%) compared to dark are as that are the body of the grain (8–15%), light areas contain less iron (53–57%) and nickel (7–8%) compared to dark ones containing iron (59–63%) and nickel (7–10%). It has been established that the features of the crystallization of the produced welded joints are an asymmetric crystallization process, a significant difference in the dimensions of the parts of the weld pool from the copper side (1260 μm) and from the steel side (670 μm), the difference in the chemical composition and microhardness of the opposite parts of the weld pool. Microhardness measurements showed that there are minor, but clearly noticeable differences between the left (170–180 HV100) and right (150–155 HV100) parts of the weld pool.

Ключевые слова Laser welding, crystallization, dissimilar alloys, copper, steel, microstructure
Библиографический список

1. Kuryntsev S. V., Shiganov I. N. Laser welding of dissimilar metals. Photonics Russia. 2020. Vol. 14, No. 6. pp. 492–506.
2. Sadeghian A., Iqbal N. A review on dissimilar laser welding of steel-copper, steel-aluminum, aluminum-copper, and steel-nickel for electric vehicle battery manufacturing. Optics and Laser Technology. 2022. Vol. 146. 107595. DOI: 10.1016/j.optlastec.2021.107595
3. Lyushinsky A. V. Diffusion welding of dissimilar materials. Moscow : Akademiya, 2006. 208 p.
4. Grinberg B. A., Ivanova M. A., Lysaka V. I., Kuzmina S. V. Explosion welding: Processes and structures. Moscow : Innovatsionnoe mashinostroenie, 2017. 236 p.
5. Grigoryants A. G., Shiganov I. N., Misyurov A. I. Laser treatment technological processes. Moscow : Bauman Moscow State Technical University, 2006. 664 p.
6. Osiko V., Shcherbakov I. Solid-state lasers. Part II. Photonics Russia. 2013. No. 4 (40). pp. 24–45.
7. Wallerstein D., Salminen A., Lusquiños F., Comesaña R. et al. Recent developments in laser welding of aluminum alloys to steel. Metals. 2021. Vol. 11, No. 4. 622. DOI: 10.3390/met11040622
8. Latypova E. Yu., Tsumarev Yu. A., Tsumarev E. N. Assessment of the bearing capacity of lap welded joints of various types. Svarochnoe proizvodstvo. 2019. No. 2. pp. 34–37.
9. Tomashchuk I., Bendaoud I., Sallamand P., Cicala E. et al. Multiphysical modelling of keyhole formation during dissimilar laser welding. Proceedings of the COMSOL Conference. 2016. pp. 1–7.
10. Artinov A. E., Karkhin V. A., Khomich P. N., Bakhman M., Retmayer M. Simulation of hydrodynamic and thermal processes during deep penetration laser welding. Svarochnoe proizvodstvo. 2019. No. 12. pp. 3–14.
11. Zhou X., Cao X., Zhang F., Duan J. Numerical and experimental investigation of thermal stress distribution in laser lap welding of Ti6Al4V and 2024 alloy plates. The International Journal of Advanced Manufac turing Technology. 2022. Vol. 118. P. 1427–1440. DOI: 10.1007/s00170-021-08019-w

12. Prokhorov N. N. Physical processes in metals during welding. Moscow : Metallurgiya, 1968. 695 p.
13. Mikheev R. S., Kobernik N. V., Kalashnikov I. E., Bolotova L. K., Kolmakov A. G. Features of applying aluminium matrix composite coatings of a tribotechnical use on steel substrates. Svarochnoe proizvodstvo. 2020. No. 9. pp. 18–23.
14. Drits A. M., Ovchinnikov V. V., Igonkin B. L. Effect of scandium doping of welding wire on the mechanical properties and structure of welded joints of aluminum alloys. Tsvetnye Metally. 2019. No. 4. pp. 67–78
15. Yum-Rozeri V. Introduction to physical materials science. Moscow : Kniga po trebovaniyu, 2013. 202 p.
16. Olshanskaya T. V. Features of crystallization of welded seams from diverse materials at electron beam welding on the example of highly chromic steel with bronze. Vestnik Permskogo natsionalnogo issledovatelskogo politekhnicheskogo universiteta. 2014. Vol. 16, No. 3. pp. 43–53.
17. Magnabosco I., Ferro P., Bonollo F., Arnberg L. An investigation of fusion zone microstructures in electronbeam welding of copper–stainless steel. Materials Science and Engineering: A. 2006. Vol. 424, No. 1-2. pp. 163–173. DOI: 10.1016/j.msea.2006.03.096
18. Kuryntsev S. V., Shiganov I. N. Welding of austenitic steel with copper by unfocused radiation of a fiber laser. Svarochnoe proizvodstvo. 2017. No. 4. pp. 7–11.

Language of full-text русский
Полный текст статьи Получить
Назад