Journals →  Chernye Metally →  2024 →  #7 →  Back

Sintering
ArticleName Influence of water temperature on results of pelletizing, sintering process indicators and sinter quality
DOI 10.17580/chm.2024.07.04
ArticleAuthor E. V. Zhenin, A. N. Shapovalov
ArticleAuthorData

Novotroitsk branch of the National University of Science and Technology MISIS, Novotroitsk, Russia
E. V. Zhenin, Cand. Eng., Associate Prof., Dept. of Metallurgical Technologies and Equipment, e-mail: zhenin.ev@misis.ru
A. N. Shapovalov, Cand. Eng., Associate Prof., Dept. of Metallurgical Technologies and Equipment, e-mail: alshapo@misis.ru

Abstract

The results of investigation of the influence of water temperature (in the range from 20 to 80 °С) during pelletizing on pelletizing results, sintering parameters and sinter strength are presented. It was found that the increase in water temperature improves the quality of charge pelletizing, mainly in terms of granule strength. This is due to the change in the physical properties of water as it is heated - a decrease in surface tension and viscosity. It is shown that water heating during pelletizing for every 10 °С provides heating of sinter charge by 1.3-1.4 °С. It was found that sintering process parameters and sinter quality improve as the temperature of water (in the studied range) used in pelletizing increases. This is due to the improved quality of sinter charge preparation for sintering, which increases of the sintered bed porosity and temperature and time conditions of sintering.

keywords Sintering, pelletizing, water temperature, surface tension, viscosity, bed porosity, pelletizing indices, sintering indices, tumbler strength
References

1. Korotich V. I., Frolov Yu. A., Bezdezhsky G. N. Agglomeration of ore materials. Scientific publication. Ekaterinburg : UGTU-UPI, 2003. 400 p.
2. Puzanov V. P., Kobelev V. A. Introduction to metallurgical structure formation technologies. Ekaterinburg : УрО РАН, 2005. 501 p.
3. Puzanov V. P., Kobelev V. A. Structure formation from small materials with the participation of liquid phases. Ekaterinburg : UrO RAN i GNTs OAO ''Uralsky institut metallov'', 2001. 634 p.
4. Ellis B. G., Loo C. E., Witchard D. Effect of ore properties on sinter bed permeability and strength. Ironmaking & Steelmaking. 2007. Vol. 34, Iss. 2. pp. 99–108. DOI: 10.1179/174328107X165726
5. Xuewei Lv, Xiaobo Huang, Jaqing Yin, Chenguang Bai. Indication of the measurement of surface area on iron ore granulation. ISIJ International. 2011. Vol. 51. No. 9. pp. 1432–1438. DOI: 10.2355/isijinternational.51.1432
6. Milokhin E. A., Batishcheva A. S., Shapovalov A. N. Influence of iron ore concentrate size on pelletizing and sintering parameters. Chernye Metally. 2023. No. 12. pp. 25–31.
7. Sibagatullin S. K., Ivanov A. V., Reshetova I. V. Application of organic binding components in the process of agglomeration of iron ore raw materials. Vestnik MGTU imeni G. I. Nosova. 2010. No. 4 (32). pp. 30–32.
8. Shapovalov A. N., Ovchinnikova E. V., Maystrenko N. A. Improving the preparation of the charge used for sintering at Ural Steel. Metallurgist. 2015. Vol. 59, Iss. 3. pp. 204-211. DOI: 10.1007/s11015-015-0085-6
9. Maystrenko N. A., Ovchinnikova E. V., Shapovalov A. N., Bersenev I. S. Improvement in sintering efficiency by surfactant pelletization of the batch. Steel in Translation. 2016. Vol. 46, Iss. 1. pp. 45-48. DOI: 10.3103/S0967091216010095
10. Frolov Yu. A. Agglomeration: technology, heat engineering, management, ecology. Moscow : Metallurgizdat, 2016. 672 p.
11. Kurkin V. M., Tabakov M. S., Kashkarov E. A., Gurkin M. A. et al. Influence of lime on sintering of a sinter charge. Metallurg. 2007. No. 8. pp. 49–52.
12. Hao Zhou, Mingxi Zhou, Damien Paul O’Deaetal. Influence of binder dosage on granule structure and packed bed properties in iron ore sintering process. ISIJ International. 2016. Vol. 56. No. 11. pp. 1920–1928. DOI: 10.2355/isijinternational.ISIJINT-2016-298
13. Shapovalov A. N., Zubov S. P., Maystrenko N. A., Bersenev I. S. Study of the efficiency of using lime in the production of sinter at Ural Steel. Stal. 2017. No. 6. pp. 2–6.
14. Bao G. The influence analysis of quicklime quality on output and quality of sinter in bao steel. Metallurgical Engineering. 2018. Vol. 5, Iss. 3. pp. 131–136. DOI: 10.12677/MEng.2018.53018
15. Oyama N., Sato H., Takeda K. et al. Development of coating granulation process at commercial sintering plant for improving productivity and reducibility. ISIJ International. 2005. Vol. 48. No. 6. pp. 817–826. DOI: 10.2355/isijinternational.45.817
16. Mo Y. P., Pan J., Zhu D. Q. et al. Improving the granulating and sintering performance by pretreating concentrates using extrusion machine. Applied Mechanics and Materials. 2011. Vol. 148-149. pp. 1351–1355. DOI: 10.4028/www.scientific.net/AMM.148-149.1351
17. Yang C., Zhu D., Pan J., Lu L. Granulation effectiveness of iron ore sinter feeds: effect of ore properties. ISIJ International. 2018. Vol. 58. No. 8. pp. 1427–1436. DOI: 10.2355/isijinternational.isijint-2018-141
18. Han F., Yang Y., Wang L. et al. Strengthening granulating and sintering performance of refractory iron concentrate by pre-pelletizing. Metals. 2023. Vol. 13, Iss. 4. 679. DOI: 10.3390/met13040679
19. Vargaftik N. B. Handbook on the thermophysical properties of gases and liquids. Moscow : Nauka, 1972. 720 p.
20. Panychev A. A., Nikonova A. P. Optimization of technological parameters based on mathematical models during agglomeration of Mikhailovsky and Lebedinsky concentrates. Metallurg. 2008. No. 10. pp.46–51.
21. GOST 25471–82. Iron ores, concentrates, agglomerates and pellets. Method for determination of solidity on droption. Introduced: 01.07.1983.
22. GOST 15137–77. Iron and manganese ores, agglomerates and pellets. Determination of tumbler strength. Introduced: 01.01.1978.
23. Shapovalov A., Dema R., Kalugina O. et al. Agglomeration process productivity increasing by a sinter mix preheating. Journal of Chemical Technology and Metallurgy. 2019. Vol. 54, Iss. 6. pp. 1344–1351.
24. Loo C. E., Wan K. T., Howes V. R. Mechanical properties of natural and synthetic mineral phases in sinters having varying reduction degradation indices. Ironmaking & Steelmaking. 1988. Vol. 15, Iss. 6. pp. 279–285.
25. Malysheva T. Ya., Dolitskaya O. A. Petrography and mineralogy of iron ore raw materials: textbook for universities. Moscow: MISiS, 2004. 424 p.
26. Shiryaeva E. V., Podgorodetskii G. S., Malysheva T. Y. et al. Effects of adding low-alkali red mud to the sintering batch at OAO Ural’skaya Stal’. Steel Transl. 2014. Vol. 44. pp. 6-10. DOI: 10.3103/S0967091214010173
27. Taira K., Matsumura M. Temperature measurement of sinter beds at high spatial and time resolution. ISIJ International. 2018. Vol. 58. No. 5. pp. 808–814. DOI: 10.2355/isijinternational.ISIJINT-2017-636
28. Shapovalov A. N., Fuks A. Y. Sintering process with gaseous fuel injection into the sintered layer. Metallurgist. 2024. DOI: 10.1007/s11015-024-01699-1

Language of full-text russian
Full content Buy
Back